JKP61G4J2 General Electric Range - Instructions

The repair was a snap! Unscrew the two small bolts holding the back of the element in place. Pull out the element so that the connectors and wires are accessible. Unscrew the two wires from the element. Remove old element. Place new element in oven. Attach the two wires to the new element (two screws), place the new element in position and replace the two small bolts that were removed at the beginning. All done. Best thing? This is a 20 year old oven, GE didn't even have the part I needed. You did! Thanks.

removed old element and installed new, and oven is up and working like new

The longest step in the fix was the walk downstairs to turn off the breaker.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.

If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.

Turn off power to oven. Make sure with tester that the power is indeed off. Disconnected the two fasteners holding the old unit face plate to rear of oven. Pull the unit outward to expose the leads. Disconnected the leads. Reform new element to remove minor bends so it will sit flat on the floor of the oven. With plies holding the leads straight connect new unit to oven leads. Push new unit back into mounting hole. Reconnect new unit face plate to back of oven. Check that unit is level. Turn the power back on. Test the unit. All works just fine.

Very simple 4 screws/nuts ...off on...done.
Best part was that I ordered the part regular shipping on a Sunday. Monday was a holiday...the part was at my doorstep at 8AM Tuesday morning. Wow that's service.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Took the element out and put the new element in place. Used the original screws - not the ones came with new element - to secure the new element back in place. DONE.

removed and replaced element as required.thank to your website i was able to order the right part.now i have your site marked as favorite.thanks for making this easy for the non professional.

Our home was built in 1990 and has an original GE oven in it. When the bake element broke in half, I thought for sure it meant buying a new oven. When I looked on line and found Part Select.com, I was impressed to find the exact part I needed. I requested the part on Saturday, and it arrived on Tuesday. I installed the part on Saturday just in time for hosting our Super Bowl party and baking enchiladas! You guys saved the day! Thanks PartSelect!

Turned the main breaker off and locked it out. Removed the original element using a 1/4" nut driver. Installed the new element using a Philips screwdriver. Turned the power on. Tha'ts it. Easy!

I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.

I pulled it out a bit and exposed where the element screws into the power.

To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.

After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.

Reset the breaker, and you're good to go.

Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.

Unscrewed face plate, unscrewed electric wires hooked to element. Cleaned out oven while I was in there...nice and clean now. Installed new element same way I took it out. Easy as 'pie'..which we'll be baking again now that the oven works.

Turned off the breaker. Removed 2 screws and pulled the element from encasement. Removed 2 screws holding the wires to the element.
Reversed the process to install the new coil.
Done in 10 minutes

Removed old part, install new one.

removed the element with 2 screws. disconected element with 2 screws. reversed order to install new element.

Shopped online for a good price for the heating element. Thw element came very quickly, very good packaging. Removed and replaced the element.