JKP07G2J4 General Electric Range - Instructions

Toughest chore was to find a tool to remove the two hex screws that held the element to the back of the oven. Once I found the proper tool, the rest was easy. Pulled the circuit breaker, removed the two hex screws, disconnected the two electrical leads and put the new part in and did everything in reverse. Probably saved over $100 doing it myself.

I removed the two screws holding it in place,Then pulled it out so
i could remove the two wires , then connected the new unit. Replaced it in the oven wall.
Turned the oven on and it worked like a new one.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Removed two screws that held the element flange onto the back of the oven, then two more little screws that held the element tips to the wires in back. Installed in the reverse sequence in about 10 minutes. A whole lot cheaper than calling a repairman! Thanks, the PartSelect customer service lady was a great help in getting me the right part for a 20 year old oven too.

First, I turned of breaker for the appliance. Removed two hex head (1/4") screws that hold element in place at back of oven. Gently pulled element exposing wires connected at base of element by hex head screws. Removed the screws and olf elelemt, placed new element in place, tightened screws, inserted into base and tightned screws for plate that holds element. After turning on the breaker, I set the oven to a low temp so I could feel the heat without burning my hand and was satisfied that the element worked.

Ordered the part on Fri. AM and it arrived Sat. PM! Could not believe how quickly it arrived. Husband replaced the old element and I am baking again! Thank you.

as you explained in the e.g.
it was the easiest thing to do for my husband, and in 10 minutes I was able to bake again.

Thanks so much for the fast delivery!!!
Sincerely Rosemarie Ressel

I removed the two screws that keep the element in place.Then I pull the element a little bit and disconnected the two wires and removed the old element. Then I reconnected the two wires on the new element then put the element back on position and put back the two screws that keep the element in place. Done.

Turn off power to oven. Make sure with tester that the power is indeed off. Disconnected the two fasteners holding the old unit face plate to rear of oven. Pull the unit outward to expose the leads. Disconnected the leads. Reform new element to remove minor bends so it will sit flat on the floor of the oven. With plies holding the leads straight connect new unit to oven leads. Push new unit back into mounting hole. Reconnect new unit face plate to back of oven. Check that unit is level. Turn the power back on. Test the unit. All works just fine.

Our home was built in 1990 and has an original GE oven in it. When the bake element broke in half, I thought for sure it meant buying a new oven. When I looked on line and found Part Select.com, I was impressed to find the exact part I needed. I requested the part on Saturday, and it arrived on Tuesday. I installed the part on Saturday just in time for hosting our Super Bowl party and baking enchiladas! You guys saved the day! Thanks PartSelect!

Very simple 4 screws/nuts ...off on...done.
Best part was that I ordered the part regular shipping on a Sunday. Monday was a holiday...the part was at my doorstep at 8AM Tuesday morning. Wow that's service.

No instructions provided, but not needed. Removed two screws holding element in place. Removed two screws connecting element to power wires. Installed new element using reverse process.

I removed the plate held by 2 screws that holds the element, pulled the coil out and disconnected the yellow and red wires. Removed the broken one and connected the new one. Very simple. I also would like to add that you people are great to deal with and I will tell everyone to buy parts from PartSelect. Your service is outstanding and fast. Thank You.

Safety first! Flipped breaker for oven in main breaker box.
Removed two screws that hold element in place.
Pulled element out approximately three inches and disconnected the two wires from the element.
Be careful not to let wires slip back into opening.
Attach wires to new element and carefully put back in correct position. Install two screws to secure.
Flip breaker back on. Turn oven on and show the little woman what a handyman you are! She might be so impressed she'll bake a cake.

The repair was very, very easy. The hard part was locating the part. I could not find it at any local hardware store. Went on-line and ordered part with PartSelect.com and it was at my front door the next day. The job was done in less than 15 minutes later. Thank You