JJW9630BCB Jenn-Air Wall Oven - Instructions

The total repair time was less than 5 minutes. I turned off the circut breaker to my oven. Directions were very easy, remove 4 screws, take plugs off old unit, place them on new unit, remove 4 screws with nut driver, place new clock in place and put the screws back in. Go out and turn on power to oven. Set the clock.

Switched off power !
Removed the control panel by removing four philips screws under the panel. marked all the connectors with a permanent markers (socket & cable) to be able to identify the right direction. Removed the old clock assembly by removing 4 hex screws.
Then assembled new unit and reversed steps...
Clock and oven temperature is again readable and very bright!
initially I got a replacement part that showed the same error as the original part, but this unit was replaced within one (!) day under the Partselect warranty plan. Good job!

First I removed four screws from the bottom of the control panel and removed the control panel to expose the clock assembly. Then removed three connectors from the clock,removed two screws from the clock and removed the defective clock assembly. By reversing the procedure I installed the new assembly and was finished in about 15 minutes.

Ordered new display module. Very fast delivery. Removed top anel of oven (5 screws) and display (4 screws) and replaced module. Very easy and fast repair.

Thanks to this web site, I discovered that this problem is very common with this oven.

Followed the instructions posted.

4 screws under the top of door need to be removed.

Pull display cover up and then simply unplug the 3 wire sets

Remove old display with the 4 nuts and replace

Plug back in and replace and you are good to go.

Appears a very common problem and a design problem with this display.

Opened breaker feeding power to oven

Removed 4 screws on underside of front panel; display module is attached to back side of panel.

Unplugged wiring harness from panel circuit boards and display module. Set panel face down on towel to keep from scratching it.

Removed 2 screws holding display to panel

Replace module and re-attached to panel

Plugged harnesses back in

Re-attached panel

Turn on breaker. Done.

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.

John - Hot Springs Village, AR

I replaced the heating element but that didn’t help. So then I replaced the oven sensor and that didn’t work either. Both were pretty easy to do but I’ve now spend $170 and my oven still isn’t working. I called number listed and got a recording that all agents were busy and there was a high call volume so I can’t get any help.

This is the simplest repair in the world! A lot of money for the part but worth every penny! Looks like a new oven. Far better than spending $4000.00 on a new double oven

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Removed 4 screws that held upper panel.
Removed 4 screws that held clock assy.
Piece of cake!

First tried the Oven Temp. Sensor, no difference. Next replaced the Electronic Relay Control Board. Successful repair. Total cost: $290.00. I removed spade connectors and molex connectors one at a time, placing them on the new board.

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.