JJW8627CAS Jenn-Air Wall Oven - Instructions

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

Shut of power to unit, removed front display panel, located lower circuit board. Removed the one screw holding existing board and installed new board, then swaped wires from damaged to new. re-installed front panel, turned pwoer back on, that was it. The unit is working well.

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

The diagram on your website really showed me the part I needed. I had may part the next day and my son who is an IT man changed the part in under ten minutes.. I was very happy, because I thought I was going to have to get a new oven. I rely alot on timed usage.

Ordered part on line, part came within few days well wrapped and protected, very simple repair removed two mounting screws and two lead wires to remove burnt element, replaced with new one, wire were re-connected and the mounting screws secured the new element in place, about 20 min job.

Turned off power at breader box. Removed the glass face of the control panel. It was secured with 4 screws. The electronic clock was attached by four hex screws which were removed with a socket wrench. There are 4 electrical connections which must be removed and reattached to the new circuit board. They are keyed so you can't attach incorrectly. Reverse the order, turn the power back on and the LED's glow bright again. Unfortunately, the first part that was sent did not work. However, on the warranty placement a new part was sent right away. The turn around time was excellent, and the new part worked just fine.

first of all you had super fast shipping only 2 days from order to repaired complete. removed 2 screws and 2 wires replaced old heat coil with new one replaced 2 wires and 2 screws less than 5 mins.

Removed two screws, pulled out element and trnasfered over lead wires. Made sure power is off first. Easy to order, easy to replace.

1. Shut off power
2. Removed 4 screws holding glass control panel
3. Unplugged 3 wiring connectors from back of control panel and removed it and laid on table.
4. Unplugged wiring connector from bad display board and removed it from control panel (2 snap tabs).
5. Installed new display board and plugged in wiring connector.
6. plugged in control panel wiring connectors and reinstalled with 4 screws.
7. Turned on power, and presto - bright new clock display! Piece of cake - 1 phillips screwdriver and 10 minutes. Anyone can do it. Thanks for a great site and all the postings - it helped me diagnose the problem and order the correct part with complete confidence.