JJW8230DDB Jenn-Air Wall Oven - Instructions

I replaced the oven sensor which was easy to replace. A pigtail wire was provided with the sensor which is intended to be installed first so you don't have to reach around the front and back of the oven at the same time. The replacement was easy. However, that turned out not to be the problem. The real problem was the maytag electronic clock control timer, temperature control unit. The part number is 7601P177-60. This device has been discontinued and I was fortunate enough to find the part at a local supplier. Once I replaced this, the problem went away. The oven heats up normally. My original symptom was that when setting the oven temperature to something like 350 degrees, the display would rapidly report heating up the oven to that temperature, and the oven was only mildly warm. If you have that symptom, it is probably not the oven sensor. It is the electronic clock unit. Hope you can find one. If you can't, I think you need to by a new oven. Regards

Replace the oven sensor per the excelent easy video you provided

removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.

Followed video

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

Replaced oven gasket and both oven hinges. Repairs did not work. Oven door is actually worst. Do not waste your time replacing the oven hinges unless they are actually broken. When to Ace hardware and bought a package of 3 super magnets for about $10. Practice placing the magnets on metal strip on outside of the actual oven vs the oven door. This metal strip is not galvanized for which the oven cleaning latch goes through. Appeared to solve the problem. I then used epoxy glue to insure the super magnets would permanently stay in place. These are dangerous magnets that must be kept away from children and pets. You will spend more time separating these magnets from each other than gluing them in place. This part I will let you figure out but the only way to separate the 3 magnets from each other is the slide them, one at a time, from each other. Now I am awaiting 4 to 6 hours for the epoxy to cure. Best of luck. Jeff

I had repair men replace the door hinges 2times and decided the 3rd time to do it myself and save some $. ordering was a chinch, received the parts in 2 days and followed instructions posted on this site. They were excellent. Just a few things I would stress: Lift UP the door to remove, not open the door fully and pull out and also make sure to take the small pins out of the new hinges before closing. They are so small you could over look them. The person who put detailed instructions on this site is to be commended for clarity and detail on "How To" I really appreciated it.

The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.

Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.

We watched the video demo & followed it step by step. The project took about 35 minutes and we replaced the hinge on each side of the oven. First we removed the oven from the wall, then dismantled it & cleaned it thoroughly, removed the old hinges and replaced with new ones. the only problem we had was that the pin holding the hinge open was missing on one of the hinges, but we cut a nail and inserted it to hold the hinge open. The job was completed quickly, and the oven door fits and works well. Thanks for the video--it really helped us.