JHC56*V3 General Electric Range - Instructions

The hardest part was working in the oven.

Turn off power
Open Oven Door, remove racks
Remove two mounting screws with nut driver.
Slide the element out to expose the wire connections.
Remove the screws and pull the element out.
Place the new element in oven.
Clamp on to each of the terminals with vice grips to keep from bending the element and install the screws.
Slide the element back into place and put the two mounting screws back in.

Put the racks back in and turn on the power and test. You may get a little smoke off the new coil.

Like I said the hardest part is leaning into the oven to attach the screws, do not sit on the oven door.

unplugged oven. removed oven racks.Disconnected old unit. Installed new unit. Very very simple

My 17 year old son and I (his mom) replaced the oven element in less than 15 minutes!!! It was so easy. We first unplugged the stove since I didn't want to go and shut off the circuit breaker in the dark!! We then removed the two screws that hold the element in place and started to pulled out the element. It was actually corroding in my hands as I pulled it out. We disconnected the wires and then put in the new element by reconnecting the wires, pushing the connections back in and replacing the two screws that hold the element in. The oven heated right up!!! What a savings to do it yourself and not have a repairman charge us extra to do a 10 minute job!! Thank you Part Select for your fast service. I will definitely look here before I shop anywhere else. Thanks,

Four screws and two wires.

removed the two screws, unsnapped the burnedout element and snapped new element in place, replaced two screws.

Could not believe how fast the part shipped. 2 days and it was here. All it took was using a nut driver to remove 4 screws and then put the new one in.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First off the part was easy to find on Partselect...

Second point... ordering was easy and shippment was fast thanks to Partselect...

Replacezment was fairly easy useing a Nut driver and a pair of pliers...took about 40 minutes.

Thank you Partselect...

Chuck

Turned off circuit. Unscrewed old element. Connected new element and screwed it in. Worked like a charm. It shipped very quickly. Could not be more satisfied; total repair: $30 and prevented me from buying a new oven; satisfaction: priceless.

Open oven door about 3 inches - then holding on the door on either side - pull up and door slides off - put it aside - this is to make it easy for you to work inside oven compartment - at rear of oven where the element goes into the back wall - there are two nuts to remove - I did not have a nut drive so used a pliers (GE could have put slots in the nuts so one would just need a screwdriver) - pull element forward - there are wires attached to the 2 ends of the element - remove with screw driver - element is off - get new part from PartSelect -(and must say pleased with their service) - and reverse above procedure.

Element was easy to remove two screws and unplug it. New element didn't have the same prongs and brace was different. Added ends to plug with screws supplied drilled new holes in oven back for brace. Works fine for a repair by a 65 year old woman.

Shut off power, Removed and disconnected element, connected and mounted new element!

My daughter and I turned off the breaker to the range and removed the old element and replaced it with the new one. My husband came home and took over after we had done almost everything ourselves!!