All Installation Instructions for General Electric Cooktop JGP333SET1SS

very easy

there were no grate pads so it was easy to add them.

Parts Used:

Grate Foot

ROBERT from CYPRESS, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

burner cap wasn't working proper.

took burner off installed new one thank you for fast shipping

Parts Used:

Burner Cap

GLENN from ST CLR SHORES, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The Grate foot is to big for the hole.

I had to drill the hole to a larger size to enable the foot to fit.

Parts Used:

Grate Foot

Harold from Broadalbin, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.

Nothing technical.

Parts Used:

Grate Foot

Chelagh from Fredericksburg, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Grate foot bdroke off allowing grate to scratch cooktop

Used scribe to remove grate foot plug still in grate inserted new foot.

Parts Used:

Grate Foot

John from Tijeras, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

To Replace Gas And Burner Parts In Section 4

Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete

Parts Used:

Top Burner Spark Electrode

John from Long Beach, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Leaking from front door

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.

Parts Used:

Grate Foot

Gene from Simi Valley, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 of 9 people found this instruction helpful.

Was this instruction helpful to you?

The spark module would constantly spark

I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.

Parts Used:

SPARK MODULE

Douglas from Knoxville, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

carbonized burners

Replaced all four

Parts Used:

Small Burner - 5K

Burner Head - Medium - 9500

Burner Head - Large - 12K

Stephen from North Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner would not ignite.

Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.

Parts Used:

Burner Head - Medium - 9500

John from Los Angeles, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

uneven flame and sputtered, burner was not useable

Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect

Parts Used:

Burner Head - Large - 12K

glen from felch, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Both items needed to replace broken or non existent ones

The burner cap was a no brainer. The grate feet should have been also, but many of them were undersized so we had to maneuver them in such a way that they didn't fall out of the grates.

Parts Used:

Grate Foot