Models > JGC9536BDB15 > Instructions

JGC9536BDB15 Jenn-Air Cooktop - Instructions

All Instructions for the JGC9536BDB15
46 - 52 of 52
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burner porsclend was cracked and would not light
removed grate and cap.unscrewed burner plate.disconnected spark wire and replaced with new part.fired it up .now it workes again.
Parts Used:
Large Burner Head
  • edward from nanticoke, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
burner ignator split--
unscrewed old ignator---replaced w new--done deal!!!!
Parts Used:
Burner Electrode
  • KARL from OCEAN, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
burner igniter didn't light burner
I removed the burner by unscrewing 2 torx head screws, disconnected wire from electrode, removed screw holding electrode, inserted new electrode,connected wire, installed burner and fired it up.
Parts Used:
Burner Electrode
  • Richard from Sanbornton, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner did not light
Ordered online Tuesday, delivery by FedEx on Wednesday. Removed the old "popped" in the new and it worked right away. It was that simple. Thanks so much.
Parts Used:
X-Large Burner Head with Electrode
  • Diane from Monee, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Damaged Ignitor
Simply unscrewed the old one and installed the new one and we have ignition!
Parts Used:
Burner Electrode
  • David from Carson City, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Electrode cracked, spark misdirected, poor lighting
After determining it would not be possible to replace the electrode only (rusted/corroded connection), ordered burner head with electrode. Part came in approx. 24 hours. Actual repair involved removing two screws (star-shaped head),disconnecting electrical clip, removing part, connecting electrical clip to new head, reinstalling two screws. Works great now!!
Parts Used:
X-Large Burner Head with Electrode
  • Stephen from Boardman, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Spark Ignitor replacement
Screws holding burner base and ignitor were plain steel. If they had been stainless they probably would not have rusted in so tight. One in the base broke off, and the one holding the ignitor could not be removed, even with heat from a torch. I ended drilling it out and re-tapping the hole. If I wasn't mechanically inclined I would have had to give up and order a new burner base.
Parts Used:
Burner Electrode
  • grant from aurora, CO
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGC9536BDB15
46 - 52 of 52