JGC8536BDB10 Jenn-Air Cooktop - Instructions

This should be a 5 min job. Lift off the burner cover, remove two screws to lift of the burner base and then remove a Phillips head screw that hold the burner igniter in place.

Unfortunately, the screw holding the burner igniter was rusted and it could not be loosened. WD-40 did not touch it. I used a stronger penetrant, "Blaster". Still it would not budge. Then I used a small Phillips head screwdriver and a hammer which I used as an impact driver. I twisted the screwdriver slightly to loosen and hit it was a hammer. Then I twisted the screwdriver slightly to tighten and again hit it with a hammer. After the penetrant and a couple of more tries, the rusted screw finally moved!!!

With no rust, this should be an easy 5 minute replacement. The burner now works great!!!

Removed the gas deflector; unscrewed the burner body; pulled off the ignition wire; unscrewed the bad electrode; screwed in the replacement electrode; reversed the steps. Voila! Perfect operation once again. My one mistake? Ordered the wrong electrode initially. Make sure you get the right part the first time around.

Replaced the spark module. Make sure you mark the wire locations on the existing spark module and install them in the same slots.

I was able to repalce without pulling the cooktop out. The access is from the bottom.

First reviewed other review on this repair. Disconnected ignitor system from electrical source (pulled plug); removed 2 screws holding casing in place; removed it from the cooktop; & removed additional screw holding ignitor. Replaced ignitor and reversed the process. Done.

Removed two star screws from the top of the burner, disconnected the wire going to the Ignitor, removed the old ignitor held in with one phillips screw, installed new ignitor and re-installed the burner assembly. Simple!

Pulled old knobs off, slid new knobs on.

Had to remove the stainless cook top from the base. Required taking off all burners. All the screws were rusted in place so had to cut off the heads with dremmel and then drill out the screw from the aluminum base. Then remove cook top after burns taken off. Cook top is double sided taped to the base, so just pull hard and it comes off.
Replace the spark control module. make sure to do wires 1 at a time as they are not in a housing.

I used a star head driver to take of burners ,then pulled wires out about 2 inches unplugged old ignitors and plugged in new ones

Remove the burner cover to reach the burner assembly. From the top of the cooktop you will see 2 screws holing the burner assembly. Using a T drive (6 point screwdriver)remove both screws and the burner assembly will come out of the cook top. Using a phillips head screw driver, remove the old ignitor from the burner assembly. Mine was galled up, so I had to use some penetrating oil and let it sit for a half hour. I then used a hammer and a phillips head screwdriver to tap the screw as I twisted to un-tightened the screw. Once it broke loose, I placed the new ignitor and reassembled the burner into the stove.

First I removed the burner, two screws held it in place. The ignitor is attached to the burner with one screw remove the screw then remove the one wire connection. Reverse the steps to put back together. The whole job from start to finish takes about five minutes.

Simply removed the old ignitor and install the exact replacement part. Work great.

First I tried twitching my nose....after I stopped sneezing I got a screw driver and put the new electrode in and gosh in gahiggy, it worked!!

First step is to turn gas off to cook top and also disconnect power to the unit. Than using a crescent wrench disconnect the gas line going to the unit from the Regulator. Than again using the crescent wrench disconnect the regulator from the bottom of the unit. Next remove the nipple that connects the gas line to the regulator from the old unit. Apply new pipe dope to the threads and screw it into the new one and tighten down. Next install the regulator to the unit and install the gas line to the regulator. once done with the install you can now plug the unit in and turn on the gas. You are now ready to use the cook top again

A crack in the porcelain caused the spark to not go in the proper direction, therefore the burner would not ignite. To have the job done by a professional would have cost $200.00 plus parts. Remove two phillips screws lift the burner out then remove the one phillips screw that held the electrode. Then with the new electrode in place reverse the previous steps.

unscrewed old ignator---replaced w new--done deal!!!!