JFI2089AEP13 Jenn-Air Refrigerator - Instructions

Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!

Simply fit the frame onto the back piece and lined up all of the anchoring plastic hooks to reattach. I had some minor difficulty in navigating the website but the customer service agent was very helpful and assisted me in purchasing the correct part. Thanks! Gretchen

Replaced two original crisper drawers with 2 new drawers; replaced broken end cap which required the removal of a few bolts and screws. The replacement parts were identical matches--a huge relief. The interior of the fridge looks like new. This follows upon not being able to get the parts directly from the manufacturer.

This grille just snapped into place without the use of tools. Couldn't have been easier. And the delivery was super fast; I ordered online one day and the item arrived the very next day.

It was very easy. I removed the two crisper drawers and the glass shelf above the pantry section. I removed two bolts with a nut driver and one screw from the slide track. I pulled out the broken piece and did that all in reverse. Took 5 mins tops.

Also I wanted to say I got my replacement part in two days with standard shipping.

Thanks to others who shared their story, I was prepared to "muscle" the front cover off the old crisper and snap it into place on the new crisper -- warning if you are good with puzzles and mechanics, this repair is a "snap"; Pantry Lid is very easy, push pin on left side, slide old lid out and push new lid in.

The broken one just popped out and the new one popped right in! This company shipped out the part I needed immediately I had it in two days!! I highly recommend them!!

took out old lid, took out drawers above this drawer to make it easier to work on. installed new drawer simple by hand with no tools. put other drawers back. very simple no tools needed.

Easy repair, nothing complicated.

Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap filter.I made that mistake! hope this helps good luck!

watched video
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.

Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.

1. Remove the crisper drawers from the refrigerator.
2. Remove the shelf from the refrigerator (a good opportunity to do some deep cleaning in the far reaches of the fridge ;).
3. With the shelf sitting securely on a flat surface, remove the old trim by using your fingertips to grab the underside of the trim and gently pull it away from the edge of the glass shelf. Work from one end of the trim to the other until the old trim pops off.
4. To attach the new shelf trim, push the trim gently onto the rounded edge of the shelf. Work from one end to the other until the trim snaps into place.

Extremely simple to replace the entire cover. Just had to press on the sides to remove the cover from the hinge pins, then reinstall.