All Installation Instructions for Whirlpool Refrigerator JFFCF72DKL01

ICE BUILD UP AT BOTTOM OF FREEZER

DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.

Parts Used:

Grommet

Gerald from COLORADO SPGS, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Cracked Door Shelves/bins

Opened the boxes and hung them in the door just like the old ones

Parts Used:

Refrigerator Door Bin

Refrigerator Door Shelf Bin (White)

Clifford from ENGLEWOOD, CO
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Tin at the top left of the panel was broken

Remove the Veggie shelf top. Remove veggie tray. Pull the clip on the center of the left panel - lift and pull forward.
Install new panel by inserting the two guide pins at the rear of the frig and move the panel to a 45% angle so you can install the veggie lid pin into position before moving the panel down into the secure position. You will hear the clip seat into position. If you do not do this I am not sure how the lid pin can be installed without breaking it.

Parts Used:

Refrigerator Pantry Drawer End Cap Left Side

FRANK from FARRAGUT, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Right side end cap cracked due to normal wear.

Very simple A) watch video B) Go carefully so you don’t break another plastic part. Took all of about 20 minutes, fit perfectly and works like new.

Parts Used:

Refrigerator Pantry Drawer End Cap Right Side

Scott from NORFOLK, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Empty box sent with no part!!!! No customer service help because of covid

No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help

Parts Used:

SHAFT

Drawer Gear Kit

Jeffery from MIDLOTHIAN, VA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Easy fix for Whirlpool refrigerator

I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!

Parts Used:

P-Trap Drain Tube Kit

John from MABLETON, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Light switch broke.

Couldn't figure out how to get the old one out till I saw the new one.Pop the old one out slide the 2 wires on the new one pop it back in place,good to go.

Parts Used:

Refrigerator Switch

Mike from New Johnsonville, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Light switch on door broke

Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.

Parts Used:

Door Switch

Donna from Oro Valley, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Freezer drawer light switch failure.

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

Parts Used:

Door Switch

HARRY from FSTRVL TRVOSE, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The door switch was broken so the interior light would not come on.

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!

Parts Used:

Door Switch

Catherine from BROOMALL, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Light switch broke

Popped out the old light switch with a butter knife from the bottom first, disconnected the plug in. Install was just the reverse. Super easy fix

Parts Used:

Refrigerator Switch

Matthew from Pensacola, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Light out.

Popped out the old switch and replaced it with the one dying

Parts Used:

Door Switch

Carlton from CHICAGO, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Freezer and refridgerator just stopped working.

The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!

Parts Used: