JFC2290REM03 Whirlpool Refrigerator - Instructions

Pried out old Switch,Hooked wires to new switch Snapped in New Unit.
5 minutes Total Time

plugged the two wires in and snapped the switch into it's socket.

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.

Looked at the appliance's booklet to see how it fit together, then installed it.

After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.

Pushed it on.

Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in

Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!

Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.

Unplugged appliance. Using a small putty knife I moved the switch out far enough to grab it with pliers. Moved wiring to new switch and pushed into place after testing.

Thanks to a very patient husband. He looked at the situation and methodically took the freezer drawer apart by trial and error and was able to replace the old shaft with the one we had ordered. We do not understand why this basic information is not in the manual or on the internet. It was relatively easy once we knew in what order to take the drawer apart.

My husband and I did this together. Most of the time was taking out all the food in the bottom part of the fridge. Once things are out, take out the deli drawer and the crisper drawers. Take out the glass over the crisper drawers and below. Now you'll see the end cap. We only replaced the left side because the plastic knob that connected the deli cover broke off. So we had to pull out the left side cap. It was hard to pop out. We ended up breaking it as we used a screw driver to get leverage in popping it out. Take off the metal drawer hardware and put on new cap. Pop the new cap in. It went in way easier than taking out the old piece. Now that you are done with that put all the parts and drawers back in place in the fridge. The deli drawer cover will pop back on the knobs. It might take a little pushing on the sides to get it in place but it will evenly pop into place like the side cap.

I watched the on line you tube video on how to DIY. The putty knife worked to pop out the switch. I used the standar screwdriver to unplug the switch from the wire harness. Then plug in the new switch and pop it back in to the roof of the freezer. Tip: watch out when ordering the new switch - the freezer switch is different than the refrigerator switch. The freezer has three prongs. The fridge has two. I initially ordered the wrong part and added a week to the repair time and had to pay shipping to return the first switch.

Removed the old pantry drawer end cap, its snaps out. Replaced it with the new pantry drawer end cap, it snaps into place. Had to line up the vent braket that affixes to the rear of the inside of the refrigerator.