Models
>
JES9800BAS
JES9800BAS Jenn-Air Range - Overview
Sections of the JES9800BAS
[Viewing 8 of 8]Manuals & Care Guides for JES9800BAS
Click to downloadKeep searches simple, eg. "belt" or "pump".

Dual Surface Element - 2500w/1200w
PartSelect #: PS11764902
Manufacturer #: W10823692
This is the replacement large surface element for your cooktop or range. It is approximately 10-inches in diameter and is 1200/2500 watts. The large surface element is installed under the cooktop and ...
$249.30
In Stock

Grease Filter
PartSelect #: PS11743870
Manufacturer #: WP71002111
The filter is made of metal and is intended for use with ranges and cooktops. As per the manufacturer, this filter may be 1/2" slimmer than the original, but will still function the same.
$35.44
In Stock

Long Oven Sensor
PartSelect #: PS1570174
Manufacturer #: 12001656
This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.
$44.86
In Stock

Element with Limiter 6 Inch - 1200W
PartSelect #: PS11764915
Manufacturer #: W10823711
Sold individually. This is a radiant surface element with a limiter, and it works in conjunction with your range. The function of this part is to give heat to the surface directly above it, on cooking area stovetop.
$244.93
In Stock

Bake Element
PartSelect #: PS11752540
Manufacturer #: WPW10310274
This bake element is found on the bottom of the oven. his bake element is for ranges.
The bake element is at the bottom of the oven and supplies the heat for baking.
Unplug the range or shut off...
$111.04
In Stock

Door Gasket
PartSelect #: PS11749287
Manufacturer #: WPW10162384
This oven door gasket comes with built in retaining clips.
$94.61
In Stock

Range Infinite Burner Switch - 8 Inch
PartSelect #: PS11744487
Manufacturer #: WP7403P239-60
This infinite switch for eight inch range burners is almost three inches long. This infinite switch is for 8-inch range burners. When an element is unable to produce any heat on a modern oven, the pro...
$66.00
In Stock

Burner Knob
PartSelect #: PS11744450
Manufacturer #: WP74011493
Sold individually. This knob accepts a D-shaped shaft.
$55.29
In Stock

Oven Rack
PartSelect #: PS11744745
Manufacturer #: WP7801P173-60
Used in the lower oven. Sold individually.
$99.70
In Stock

Infinite Switch - 8 Inch
PartSelect #: PS11744412
Manufacturer #: WP74010824
Sold individually.
$89.19
In Stock

Meat Probe
PartSelect #: PS11744536
Manufacturer #: WP7430P038-60
Also known as Heat Probe or Gauge. This probe is used to check the internal temperature of the meat to ensure proper temperature is reached.
$180.87
In Stock
Questions And Answers for JES9800BAS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JES9800BAS
[Viewing 10 of 10]Element will not heat
Fixed by
these parts
these parts



Show All
Little to no heat when baking
Fixed by
these parts
these parts



Show All
Will Not Start
Fixed by
these parts
these parts



Show All
Oven is too hot
Fixed by
these parts
these parts


Show All
Oven not heating evenly
Fixed by
these parts
these parts



Show All
Touchpad does not respond
Fixed by
these parts
these parts



Show All
Door won’t close
Fixed by
these parts
these parts


Show All
Will not program
Fixed by
these parts
these parts

Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
these parts

Show All
Little to no heat when broiling
Fixed by
these parts
these parts

Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace Grease Filter
Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.
Parts Used:
-
Gene from Washington C.H., OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
524 of 536 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right rear burner went bad
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip charge. It was easy!!
Parts Used:
-
Mark from Loxahatchee, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
141 of 157 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Parts Used:
-
David from Westford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
152 of 190 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!