JEC9530ADS Jenn-Air Cooktop - Instructions

the cracked knob left the round piece of metal that is part of the knob inside the stovetop, preventing the new knob from being installed at the right height. We were able to remove the metal piece and place the new knob on at the correct height. We were very pleased at how fast the part was received.

Shut off 220 volt power to range. Removed two screws for cooktop element access. Used needle-nose pliers to remove power (2) and control (2) lugs and wires. Remove defective cooking element module, replaced. Reverse steps for new unit.

Disconnect the power.took the cooktop off the range. Turned it over. Removed the underside plate. Disconnected the bad element. Pluged inthe new element. Replaced the under plate. Reconnected the range to the stovetop .put cooktop in place. Reattached screws. Turned on power. Worked perfectly.

Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.

It's easier with two people.
1 - Turn the breaker for the range to OFF
2 - Verify power is off by testing the burners and lights
3 - Remove front two screws above oven door jamb
4 - Lift the top and prop it up with the spoon, or have your helper hold it.
5 - Loosen the screw at the rear of the bracket that holds the elements against the glass top (front and rear are held by the same retainer)
6 - Remove the bad element by sliding it sideways from the retainer. Do not disconnect things yet.
7 - The burner has numbers around the edge. Move brackets from old element to new one, matching the numbers. Then move wiring to new element. New burner may have a single connector where old one had 2 and a jumper. If so, ignore jumper.
8 - Slide new element under bracket and reinstall the screw.
9 - Lower the range top and re-install the screws.
10 - Turn on power and test.

i did fine

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.

OMG you have no idea how grateful I am. My husband and I watched your how-to-video and decided that it looked pretty easy for us to replace on our own. We saved close to $200 between the flat fee for a service call plus labor. Thank you very much. We were also pleased how fast our part was shipped to us.

1. Remove power from unit. 2. Removed 1/4" sheet metal screw from lower blower vent tube. 3. Lifted the unit above the counter and placed two 1x2" boards between the unit and counter. To remove the Stove Top to get access to the Element you must remove 8 each 1/4" sheet metal screws from the bottom side of the Stove Top attaching flange. 3 each screws on the forward and aft side and 1 each on the left and right side. (Note, the 8 each 1/4" attaching screws are at the top of the Stove Top attaching flange.) 4. Remove the Vent Grill and locate the 2 each cross point screws on the center left and right side of the opening. (Note. Due to the limited space, I used a right angle cross point driver.) 5. Remove Stove Top. 6. Tag electrical connections. Remove and replace Element. 7. Turn on power and check Element. Remove power and Reassemble Unit.

My mother is a great cook that is always in a hurry ... and I know that she is not always pushing those plastic knobs DOWN before turning them. Frustrated with reordering these expensive plastic knobs,I decided to get smart. I reordered 6 knobs (this is the 3rd time in 2 years). These knobs are designed to break. I decided to reinforce the plastic that goes around the knob shafts. At first, I thought about using some rigid metal bird bands like on a parrot. I second thought that this would be too difficult to find the perfect size to fit the outside diameter of the knob, so I decided to buy slightly smaller diameter, tightly coiled, sturdy, steel springs to fit around the plastic that fits onto the shafts. I manipulated each spring to become slightly larger to fit over the plastic by twisting the spring in the direction of uncoiling it. Not permanently unbending it, but just enough to make it grow in diameter to fit around the outside. I clipped the excess wire from the spring with wire cutters and reinforcerd everything with a coat of good strong epoxy . It seems that the metal spring and epoxy bonded to the knob became SOLID AS A ROCK. I figured, if the plastic can't split from the D- SHAPED shaft, then we have a knob that is as good as if it were made out of metal.