JEB1095BB03 General Electric Microwave - Instructions

John from POWHATAN, VA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

When door opened, microwave would turn on

Removed the outer cover to access the door switches. Turns out there were three switches, but I determined that only two were bad. When the small colored tab on the switch is pushed in it should make a clicking sound. The two bad switches had no resistance and did not make any noise when pressed. Removing the switch is relatively easy, you simply pull it away from a couple small tabs holding them in place. After reconnecting the wire leads, insert back into the holding tabs and install the cover.

Parts Used:

Tom from SUN PRAIRIE, WI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Unit would run when door is opened

Two screws to remove upper from vent. Two screws to remove the didgit panel lift ip to remove and put aside remove the two screws that hold the door sensors. Depress the tab to remove the defective sensor disconnect the electrical connector and replace the new sensor snap it back into the holder install the two screws, install the didgital panel and vent panel to complete the job. Please be aware that there is a video of this procedure on Y tube

Parts Used:

Ernest from RIVERSIDE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

NO light

.Thank You Dan

Parts Used:

Dan from Leesburg, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

microwave Quit working but lights worked

llation

Parts Used:

Rick from Muncie, IN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Microwave will not start

Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.

Parts Used:

Carlos from GLENDALE, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Still runs even the door was open

Pulled it from the wall remove the front vent covers removed the control panel remove the door switches by a special screw driver bit which looks a star remove the electrical terminals pressed the plastic clip pulled the switch replaced it with new one then followed initial steps backward

Parts Used:

Erwin from CONROE, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Microwave would run but not heat

Removed the control panel, one screw at the top. Removed 2 screws on the door switch holder and removed the door switch. VERY EASY.

Parts Used:

Timothy from MAYSVILLE, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

bulb burned out light that is under the microwave, which lights the oven below.

thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)

Parts Used:

Gary from UNIVERSITY PA, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Under the microwave there are two light bulbs that light up the top of the oven/range.

Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.

Parts Used:

Janet from TREASURE IS, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Light bulb wouldn't light.

Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.

Parts Used:

Steven from Marina Del Rey, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.

Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.

Parts Used:

Leon F. from Brookline, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

time would count down but unit would not run & heat.

remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.

Parts Used:

Bill from Shawnee, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Interior Light Out

Removed Cover Plate,
Removed back cover
Bulb disintegrated removed base with pliers
Screwed in new lamp
Replaced cover
Done

Parts Used:

Steven from Waldorf, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

light bulb burned out

took out several screws dropped down the panel under the microwave and unscrewed the bulb and put the new one in. It was a simple job.

Parts Used: