JDE2000A Jenn-Air Dryer - Instructions

Lifted top lid of cabinet using putty knife to release clips then removed front panel. Removed drum from unit and set aside. Found that one of the drum support roller wheels had lost the rubber roller. Removed old roller and secured new one which was an easy fix.
Installing the drum belt was a bit more difficult as I had to do it alone. I threaded the belt through the pulley/control arm and held it taugt with one hand and then inched the belt around the drum while holding it in place with my knees. Took awhile but I got it secured. Would definitely help to remove one of the side panels of dryer or have someone assist you.

Released lid clips, two screws removed to remove the front. Took tension off of the belt by removing it from roller, then lifting tension spring from base. Removed drum to gain full access to motor. Lubricated rollers, vacuumed all areas to remove lint. Replaced motor and belt. Re-installed drum and re-attached tension spring, dryer face, and top. Works fantastic. Hard part was getting spring released and reattached due to location.

The new blower fan was made of molded plastic in which the hole internal diameter contained extra material

Lifted top from dryer and fuses were in the back of drum just below heating coil. Used nut driver to remove heating coil to gain access to fuses and replaced them. Process was quick and easy. Diagram from this site made locating fuses elementary!

P.S. I have no certified experience in appliance repair.This was my first time ever and dryer works perfect.

Turn circuit breaker off, unplug for added safety. Use a medium flat head screwdriver and lift the top up. Use a nut driver to remove two screws holding the front panel to the frame. Remove the front panel and begin to dismantle the blower wheel. Remove the outer clamp from hte motor shaft, then the U-clip (inexpensive plier that has to pins to open the U-clip.... tricky little bugger). Pull the blower wheel off and replace with the new wheel. Reverse the proedure and your ready to go.

I just removed 1 screw that held the safety thermostat in and replaced it. Then I removed the long screw that holds the heating element and the high limit fuse in place. Replaced the fuse, cleaned out the lint duct area. Closed the dryer lid and pluged it in, it worked fine.

Took the front off, took the shield off, replaced wheel and retainer clip. Replace wheel and reversed procedures. Easy as pie.

Checked the voltage to the high limit switch. Found that the element was bad. Ordered the part from partselect.com. and received the part in two days. Unplugged the unit, pulled the lid on the dryer, used the 5/16" nutdriver, removed 3 or 4 screws, pulled out the old and installed the new. Saved a $100.00 service call from the repair man! Novice in home improvement can do this. Thank you Partselect!!!

i followed part select instructions that probable cause was either thermal fuse or high limit thermostat.put ohm meter across both & saw thermal fuse(has pink dot on it) part 53-1182 was open.ordered thermal fuse replacement kit. part#LA-1053. the problem i had was after reaching down the side of heating housing removing the bracket with the thermal fuse,replacing & reconnecting it i had a hard time reinstalling the bracket,very tight space & i don't have very big hands.finally got the fuse in it's hole in the bracket & slid & jammed the bracket into the side of the mounting housing & it stayed secure.dryer started

I pulled front off drier old wheel was easily removed because it was broke in half. New wheel fit tight and took a little effort to get new wheel installed. Installed retaining clamp to shaft and vacuumed out lint before putting front back on.

I googled 'replace dryer belt' and found instructions on the 'Virtual Repair Man' web site. After reading the instructions through twice I began.

First I removed lent filter and removed the two screws that hold the lent body in place. I rotated the top panel up and back and leaned it on the wall; proped up the dryer drum with some scrap wood pieces; rotated the front panel of the machine out enough to slip the new belt, groves down, around the drum; reinstalled the idler pulley under the drum; raised the drum slightly and reattached the front panel. Reattached the top panel and replaced the filter. Did a test run and worked good.

I got a price from Sears for the part and they were asking $45 just for the belt. I saved enough in parts and labor to take my wife out for a real nice dinner. thanks

Worked with a guy, I'm a girl. He had a good "feeling" about how to take apart the dryer, install the belt and put it back together. After one go putting the belt on, starting the dryer and having the belt come off....I followed along silently looking at the directions. Definately needed 4 hands to put the drum back in alignment. Other than that, this was very simple PROVIDED THE DIRECTIONS TO REALIGN THE DRUM are followed at the end. So simply: my directions are meaningless here, just follow the ones enclosed with the belt and this should take no more than 1 hour. :)

Dont go in through the back!! Take the top off then the obvious steps to get to the drum and belt. On the kitchen aid model at least I would advise to make all the hassel of replacing the belt well worth your time to go ahead and buy a new tension pulley with the wheel on it as opposed to the all metal tension pulley. My dryer is much more quiet now and seems to be more efficient.

I waited a two days to get my belt then deciced to get a new tension pulley. Ordered it one day and the next it was at my door. This was well worth my time and effort. Thanks PartSelect!!

Took the top off then front off of the dryer with just 2 screws( thank god not the back) and replaced the belt...had a difficult time getting the tension pully in place, belt kept falling off..the stop screw for the tension pulley was bent ,so had to replace that first.

Pry up front of top and lay back. Remove two 1/4" srews at top corners. The front of dryer will then swing to the right. The drumb will lift out easily. Remove broken belt. Inspect the drum rollers on the back wall. Replace if loose or not turning. Mine needed replacement. The assembly part is not easy. You need the drum in place and after it is in place you can't get the belt on. After 8 tries I got smart and made a prop to hold the idler pully up, then put the belt in place and let the pully down slowly. It worked! Put the front back on and the 2 screws and pop the top back down. Also it is a good idea to unplug the electric cord and turn off the gas (if app).