JDB9800CWS3 Whirlpool Dishwasher - Instructions

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.

Two of the four small nylon/plastic tabs on the adjusters that support the top rack on the rack slides, broke off (one on each side).

Before the new parts arrived, I printed the limited (but definitely helpful) instructions that were available and familiarized myself with the adjuster assemblies.

As practice, I took one adjuster assembly apart making notes of any "gotchas." The main gotcha I found is that the nylon/plastic parts are easy to break (obviously) as prying is involved during removal and replacement. It took me about 20 to 25 minutes to take one side apart and about 10 minutes to put it back together again.

When the new parts arrived, I was able to do the first side in about 10 minutes (removal and replacement), and the second side in about 5 minutes, all because I had printed the instructions, familiarized myself, and practiced. I hope this helps.

I basically used the instructions provided with the "Your Order Has Shipped: email from you. It was quite easy. Thank You!.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Thought this would be much easier than it actually was. Long story short, ended up calling is an appliance professional to install the part.

I did a Youtube search and discovered there were a couple that showed the replacement in detail. I watch the entire process once and then had my laptop beside the upper rack and paused the video after each step. That worked well

Removed old housing parts and replaced them with the new parts I ordered. Very easy

The old filter simply unscrews and the new one screws in.

pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.

In looking at the parts catalog the part I needed didn’t state left or right side piece. I understood that the same part was used on both sides. Knowing the other side may fail also I ordered (2) pieces. Once they arrived I took apart the surrounding element using a screw driver to pop the enclosure apart carefully. I noted where each clip went and re-assembled the enclosure.

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

Laid on my side amd reach under unit

pushed the new retainers in the holes and we are set to go

Unplug dishwasher. Remove lower front accessible panel. Disconnect wires to the drain pump. Rotate pump to unlock and remove. Apply plumbers grease to rubber seal and install new pump. Connect wires. Plug in dishwasher and run rinse cycle to check for no water leak. If all okay replace access panel. Done.