JCSP39WV1WW General Electric Range - Instructions

i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!

First turned off the power to the stove at the breaker panel, thenI removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Disconnecting/reconnecting the "clips" was the only difficult part because they did not slip off/on easily. Replaced the element in the oven, replaced the screws...good to go!

Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!

I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!

Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical to wall outlet. Turn on burner element and verify that it works.

Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top install nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!

Turned off juice
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble

took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

I went by the video

Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit breaker back on, turned the oven on.... made brownies (o:

Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)

Turn off power at the circuit breaker before working on electric thing.

Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.

Removed old broken element and installed new one. Took less than 10 minutes

Fast shipping, Very easy to install I am a senior and had no problems works Great!!