JCGS650DEF1WW General Electric Range - Instructions

The job was made very simple primarily due to the repair video that was available on your site when I ordered the part that I was looking for. The job can be done in less than 15 min, but it took me a little bit longer because of some rusted screws that didn’t want to come out so easily. I also decided to take of the front door (not mentioned in the video) just to make it a bit easier to reach the igniter component. The door comes off very easy by opening the door about 6 inches and pulling up and off of the door hinges. Again for a novice like me the video was a life saver.

I was at my in-laws and they expressed how they needed to buy a new stove, since it stopped working. They explained the problem to me and I immediately checked the broiled (it worked fine). Knowing that stoves have 2 electric igniters, i knew 1 was bad.
The site got me the part in 3 days (regular shipping).
The repair was pretty easy.
- Removed 2 screws that hold the floor of the oven.
- Removed 2 nuts that held the igniter to the oven.
- Removed the bottom drawer of the oven, and unplugged the igniter.
- Finally, I screwed in the new igniter, fed the wire down to the plug and plugged it in.
- Then I tested the oven before putting it back together, IT WORKED!)
The only negative was, when I was removing the racks and pans from the oven, one of them happened to be filled with oil for frying, and it got all over me. Be prepared for anything when working on someone else's appliance.

new igniter had a plastic wire coupling that did not fit with the soves wires; cut off coupling and connected wires with ceramic wire nuts given, remounted ignitor and fired up the oven.

Nylon support is attached to the oven frame with a screw having a .25 inch socket head. The screw is mounted in a recessed opening on the support, so a socket is needed. I needed to purchase a proper size socket from the hardware store for a few dollars since the smallest one I had was 7mm. I guessed at the size and was correct. Repair was easy and took a few minutes.

Removed oven convection fan cover for more room to remove/replace lower oven bottom. Deflector is attached underneath oven bottom and you will need new self tapping sheet metal screws to replace old ones. My deflector actually had hole melted in it from glowbar igniter directly underneath it. Glowbar remains white hot until selected oven temp is reached...poorly designed.

I unplugged the power then removed the shield from in front of the valve location. I removed the wire shield and pulled the wire connector into the burner area. I unplugged the wire then removed the burner frame pulling it out, I removed and re-installed the igniter kit. I also had to cut the connector from the from the old igniter (about 3" up)then remove the connector from the new (cutting flush to that connector) and switched out the connectors using the porcelane wire ties provided with the new unit. I then re-installed the burner frame making certain that the wires were in the proper location. I plugged the connectors together ensuring proper locking, pushed the wires back into the hole, replaced the wire shield and then the valve cover shield. Restored power the igniter lit brightly and approximately 4-5 seconds later the oven burner lit. I checked connector because another person on the site stated that it may be the wrong one and that the wire connectors would be sent in case that were so.

I got my part in a couple of days during christmas and still got at pretty quick it was 5 screws unpluged the old one pluged in the new one put screws back and we were ready to cook, did all from inside the oven did not even move the stove very simple!!

Replaced the igniter. Quite simple.

I went on line found your web sight selected the igniter kit required for my stove. Your web site made it easy to select the part I needed after reviewing the diagram. It was very easy to install just unplug the old unit and plug in the replacement. I would recommend this site to others.
I saved a few dollars; just think if a tech had to come out?

First I took off the oven door which was a snap. Then I removed the bottom drawer. I removed the i guess you would call it the spill pan which was two screws. removed the guard plate and disconnect the igniter and remove the two screws that was holding it in place. Peace of cake.

Replaced the ignitor in the broiler. Two screws holding the ignitor in place and two to the cover holding the quick connect plug.

Bake ignitor would not glow. Removed racks and lower pan to access the ignitor. Removed two attaching screws and unplugged electrical connector. Installed new ignitor. Hint: Gas will not flow unless both the bake and broil ignitors are operational. Ignitors are interchangable; you can test ignitors by swapping them.

replaced the ignitor and it has worked perfectly the last week - Service repair walked away from the service call stating it was too random - you website state 91% cause, you were correct I wish I had done this 2 years ago

igniter was not glowing bright...removed old one and installed new one all within 30 mins.Part was exactly as description and picture really helped. Turkey for Thanksgiving will be served cooked by my oven.Thanks.. Daniel

Remove the warming drawer to get to the electrical connection, Remove two nuts from igniter, replace igniter fasten the nuts and connect electrical. Oven works fine. BEST PART OF THIS......SAVED $250.