JCBP84DPBB General Electric Range - Instructions

popped out the remainder of old lens, then pushed in new ones and slipped on plugs.

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Took 5 minutes to repair easy peasy??

THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.

Ensure washer drum is empty of water before attempting repair. Disconnect the power to the appliance. Remove the front washer panel (a metal putty knife if needed to unlock the two upper tabs which releases the panel). Locate the existing drain pump at the bottom of the unit. Disconnect the two wires from the drain pump motor (one orange, one black/white). A pair of pliers and a gentle pull should do it. Using a small ratchet and socket, loosen and remove the two bolts that secure the drain pump to the bottom panel of the washer. Using a pair of pliers, squeeze the factory hose clamp on the large drain tube that connects the pump to the drum and remove the hose from the pump, being careful to capture any residual water from the drum. A towel is helpful to absorb the water. Repeat for the smaller discharge drain tube located on the side of the pump. Once both tubes are disconnected, remove the old pump. Install the new pump and reconnect everything in reverse order. Connect the small drain tube to the side of the pump. Connect the large drain tube from the drum. Ensure the clamps are properly secured. Insert and hand-tighten the two bolts that secure the pump to the bottom panel of the washer, making sure the bolts are snug but being careful not to overtighten. Reconnect the two wires to the motor. Restore power to the appliance. Run a quick wash cycle to ensure pump is working correctly and check for any water leaks. When satisfied, reinstall and secure the front washer panel.

I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.

To Install.
Reverse steps above

Exactly how your perfect video instructions showed me. Thank you for a job well done!

Follow the instructions from YOUTUBE to replace the new drive belt..

Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .

I followed the directions I found on my tablet on youtube.

Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.

It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.

If I were to do it again, it would take 30 minutes or less.

First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!

Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)

1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.