All Installation Instructions for General Electric Range JBS03BC1WH

Oven heating element broke

Turn off the power at the breaker. Use hex head bit from 4 in one screwdriver or 1/4 inch nut driver. Heating element comes out, take off wire clamps and install new piece. Put screws back in, turn breaker on and that's it!

Parts Used:

Bake Element

ryan from NOVATO, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

burner not work

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

SILVIA from Midlothian, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Porcelain melted on burner

Simply shoved the new one into place.. tada done. Woohoo thanks

Parts Used:

SURFACE HEATING ELEMENT

Catherine from PICKENS, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Defective switch

Replaced element control switches

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Mary from EDENTON, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Needed new drip pans

Replaced drip pans

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Patricia from GORDONVILLE, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

It was burned out

I just follow Steve's Installation Vidio. My range works.
Thanks Steve

Parts Used:

Surface Burner Terminal Block Kit

lan from SANTA CLARA, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Surface burner stopped working & light indicator remained on

It took my son very little time to install control switch. Using a screw driver he removed the back panel directly behind burner units & replaced the control switch. Very easy.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

Cynthia from BALDWINSVILLE, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

front lift burner not working and surface light on with everything off

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

kevin from GAYLORD, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

someone sat on cooktop and dented it

took off burners, removed screws one at a time, only tough part was getting to grounding screw so i took off back plate (easy) to get to grounding screw. i recommend doing it all at once with no break so you remember where screw went, or mark them with sharpie. it was fun once i got started. good experience and now it looks like new. plus i didn't have to clean the old one.

Parts Used:

COOKTOP WHITE

Daniel from Osseo, MN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Terminal block connectors worn out wasn’t making a good connection with the stove top burner

Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.

Parts Used:

Surface Burner Terminal Block Kit

Lance from HAHIRA, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Was burned out

Took back off and replaced.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

BRINDIA from DOVER, TN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

oven racks very old and writing on knobs worn ff

Very was ti replace racks and knobs. Very fast mail service

Parts Used:

Oven Rack

Patricia from SAN JOSE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

broiler unit went out

less then ten minutes, used a electric screw driver and in a snap, finished, I always buy my parts on line at parts select my stove is old but in good condition except parts give out sometimes and I just order part and keep on cooking.

Parts Used: