JBP70WC1WW General Electric Range - Instructions

I simply turned the power off and slide the stove forward to give myself room to get behind it and just unscrewed the cover behind the burner switchers and pulled the switch knob off then I removed the two small screws that hold the burner switch to the control panel and go to the back and pull the wires carefully and replace them on the new switch one by one and screw the new switch to the control panel and replace the back panel and done!

well first i came here thewn i called got my part the next day by the way paying only regular postage. it took me more time to pull the stove out and find the sockets then to actually put the element in.that took a whole 3 minutes. thanks partselect you guys are the best and i will be back.

Replaced element control switches

First I removed the five screws that hold the
element in place and pulled the element out
about 3 inches and disconnected the two wires
and hooked a piece of wire on the leads to make sure they did not fall behind the cabinet.
Then I connected the new element to the lead
wires and removed the piece of wire and secured the new element in place with the mounting screws. Took about 25 minutes to remove and replace.

couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came with new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.

Removed door from range(see manual for instructions). Set door face down on protective cloth material .Remove two top screwws, 3 bottom screws and lift back of door off. Remove two screws on each side of door bottom channel and remove channel. Put in new trim on bottom of glass window and put screws back in. Set back of door on top of front cover and screw two top screws and 3 bottom screws back in. Set door back into range. Lock clips on both hinges.

On a 18 year old electric GE range: amazing not the exact handle but it does fit perfectly and looks great. If your somewhat handy this is very easy and can be completed in less than a half hour. Save the screws from the old handle, they can be used again.

Lots of jiggling until I found the screws to remove. After finally getting the top off the base there was the Instructions on a pamphlet taped to the bottom. The key tho get the top off is to remove the face and remove the proper screws( they are identifiable)unplug the electric plug 2 screws on the back sides and poof it is free!

The part was exactly what we needed. However, we didn't find the video online to show how to replace the part until we were almost finished. (https://www.youtube.com/watch?v=ovwcJhfWHXQ) If we had found the video, it would have saved us a lot of time because we undid more of the door than we needed to. Also, the video tells you exactly what size tools to use. However, taking the door more apart allowed us to clean more of the inside of the door. So, watch the video before you start, and also, be prepared to spend time cleaning the insides of the door. Also, when we put the door back together, we accidentally turned the front glass panel of the door upside down and it wasn't noticeable until we had put the door back on the oven. So, we had to take it apart again to fix it. All said, we're very happy with the new part. Thank you PartSelect!

The only hard thing was contorting my old beat up body and joints long enuff to reconnect the 2 wires and oven heat sensor and put in 6 screws with a 1/4" nut driver. I did remover the oven door and that made it much easier for me.

We ordered the part, it arrived quickly my husband removed the burnt out element. We took the back off the stove in order to install the new part. It was easier to connect from the back than reach in to the oven. An easy repair and the stove works fine now.

First I removed the screws and popped off the existing element. One of the wires "disappeared" back into the insulation, so I had to remove the back panel of the oven to access that wire and push it back through the opening. Then I attached the new element to the wires and replaced the finishing screws.

I had my husband fix it! Very easy for me.

It didn't take him long. The most difficult part was getting to the screws. He had to practically climb into the oven.

The parts were shipped promptly and the whole process was relatively painless!

The repair was so simple. First i killed the circuit breaker then removed five screws upluged element from contacts and removed the element plugged new element into the contacts popped the screws back and was done.

Unplugged the power supply. Took off the cover on the back of the unit. Unplugged the wires to the broiler element. Removed the bolts(4) holding the element inside the oven. Removed the temprature sensor from element and took it out. Put it all back the way it came out. Worked great. Took 25 minutes.