JB905TH4WW General Electric Range - Instructions

First I removed the five screws that hold the
element in place and pulled the element out
about 3 inches and disconnected the two wires
and hooked a piece of wire on the leads to make sure they did not fall behind the cabinet.
Then I connected the new element to the lead
wires and removed the piece of wire and secured the new element in place with the mounting screws. Took about 25 minutes to remove and replace.

I thought it was the burner thermostat, so I replaced the burner unit. By coincidence, the ceramic outer portion of the burner was cracked in two places, but otherwise intact. That was not the problem, though since the new burner did the same thing as the old one. Then I new it was the Infinite Control Switch, so I ordered it. Replacing it was easy. I turned off the cooktop circuit breaker and made sure no power was going to it. It is powered by 240 volts so you need to be very careful to turn off the power before doing any servicing on it. I then carefully pried up the glass cooktop and lifted it out, so it wouldn't break. By taking off the control knobs, and removing several small Phillips head screws all around the metal cooktop frame and just under the edge of the glass cooktop, I could lift the glass top off from the cooktop, and place it on some newspaper so it didn't get broken. It is important to keep the rest of the cooktop upright. The burners are not fastened down, and only gravity holds them in place. They normally sit on two springloaded pins, one on each side, and the weight of the glasstop pushes them down to their proper setting. So don't mess with them, and make sure each side remains on the two pins after you're done and before putting the glasstop back on. As for the switch, you need to remove two small 1/4 inch metal screws (a socket is very handy for this), one on each side of a metal framework that holds all the switches. After removing that framework, I carefully turned it over and found the correct switch for the burner that wasn't working. In my case, it was the closest right hand burner, which is also the biggest and has the option of having a big, small or both elements turned on, depending on how you turn the control switch. I then carefully pulled off each wire lead, with a needlenose plier to avoid damaging them, and immediately put each wire onto the corresponding same connection on the new switch. Take a close look at the wires on the old switch to make sure you plug them into the same connectors on the new switch. It's pretty straightforward. There may have been one or two small screws holding the switch onto the framework, but I don't recall right now. It was very easy to see how to remove and then reattach it. Then reverse the above steps and reinstall the cooktop, turn on the power and you should be in business!

after removing the two screws that are just inside the oven, I propted the top open with the box that the part came in. I drew and labeled the wires as I took them off using a color coding. next I removed the two clips that held the burner in place and marked on the new burner exactly where the clips were attached. Replacing the clips was possibly the hardest part of the whole operation. When you replace the burner, don't forget to replace the insulation pad that is stuck one the metal where the conections are. I missed this and had to reopen the stovetop and slid it on after I was finished. Otherwise it went pretty smooth.

couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came with new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

Pulled the stove out from between the cabinets, used a blade screwdriver to pop the oven door retainers down and lifted the oven door out, removed the racks. used a 1/4'' nut driver to remove the 5 screws holding the broiler in place. From the time I unplugged the stove from the outlet until I plugged the stove back in was 15 min. I would suggest wearing gloves because the metal frame around the burner element has sharp edges.

Turn off power to cook top. Remove 2 screws that hold the cook top to countertop. Lift complete cook top from counter and place diagonally across opening. Remove 10 screws that hold glass top to the component cabinet. Make a diagram of wiring to element. Disconnect wires. Remove 2 mounting brackets from bottom of old element and position them on new element and screw tight. Wire new element as diagrammed earlier. Replace glass top on component cabinet and reinstall 10 screws. Place unit back into counter opening and secure with 2 straps. Turn power back on. Stand back and enjoy your accomplishment.

replaced lights in refrigirator and freezer

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.

Not only did we (my wife did help) replace the dual element but afterwards we realized the control switch was not functioning properly and so that was replaced as well, and now our appliance works as intended. Also the instructions, are helpful as well. We used care not to force or over tighten anything and with two sets of eyes and the extra hands everything went much better. Anything that was removed was noted as to it's location and replaced .

Removed door from range(see manual for instructions). Set door face down on protective cloth material .Remove two top screwws, 3 bottom screws and lift back of door off. Remove two screws on each side of door bottom channel and remove channel. Put in new trim on bottom of glass window and put screws back in. Set back of door on top of front cover and screw two top screws and 3 bottom screws back in. Set door back into range. Lock clips on both hinges.

I removed the screws from the underside of the stovetop, lifted up the top, propped it up to keep it from falling (using a large book), and removed the old burner by unscrewing it from the top and removing the wire connections. I then screwed the new burner into the top, and attached the wires back to the burner, dropped the top down (gently and carefully, of course), and screwed the top back down to the rest of the stove. It was fairly quick and painless. Although, putting the stove back into his position was not easy, but that was no fault of the stove!!

Would have helped it I knew the push on terminals of the bake element were visible and accessible to slide the terminals on from the back side of the stove in the beginning. There is not enough slack in the the terminal wires to connect them from the oven side, so you will have to open the back panel to retrieve a wire anyway. SO, CONNECT THE BAKE ELEMENT TO THE OVEN WALL FIRST ! Then, open the back panel of the stove and simply slide the terminals on the exposed slide terminals of the bake element.

Turn off breaker, disconnect electrical wiring, remove cooktop from courter top, turn over , remove switch.