All Installation Instructions for General Electric Range JB655DK3WW

Broken glass

Easy install, clean all fastener locations.

Parts Used:

Range Oven Door Outer Panel

Edward from PERKASIE, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Element went out in glass top stove.

Unscrewed the stove top and replaced the element.

Parts Used:

Haliant Element - 12 Inch

Aleshia from O BRIEN, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Front glass broke

Really easy repair, two bolts on the inside of the oven door release the handle assembly, and four more bolts, two on each side, to release the handle from the frame. Then slide the glass into the placeholders and reverse install.

Parts Used:

Range Oven Door Outer Panel

Jeremy from PALM BAY, FL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

blew out board by crossing wires..mistakenly toke out bulb assembly to replace bad bulb

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..

Parts Used:

CONTROL OVEN TO9

Ken from CALABASH, NC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Incorrect oven temperature due to defective temperature sensor.

Performed repair using a video for reference.

Parts Used:

Temperature Sensor

Anthony from FARMINGVILLE, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Switch was not turning off range indicator light

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Charles from PORTLAND, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

previous owner self cleaned and left oven racks in the oven

threw out the old ones and slide in the replacement ones from you.

Parts Used:

Oven Rack

Judith from San Antonio, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

would not get hot

Remove 2 screws and 2 wires- took the coil, then installed the wires and put the screws in--works fine. Thanks for the fast service.

Parts Used:

BAKE ELEMENT

Janice from PENSACOLA, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The right side Large/Small burner control failed.

The burner remained on high regardless of the position of the control. 1. Unplug the range. 2. From the back of the range control panel, remove the top-plate that covers the controls. (4 screws) 3. Remove the two screws that hold the control knob in place. 4. Move ONE WIRE AT A TIME from the old control knob to the new gripping the connector only (do NOT pull the wire). 5. Remount the controller and reassemble the back cover with four screws. 6. reconnect the range and test.

Parts Used:

Range Surface Element Control Switch

JAMES from ORMOND BEACH, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

OVEN CLOCK CONTROL MALFUNCTIONED

I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.

Parts Used:

CONTROL OVEN TO9

Gregoire from N CHESTERFLD, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Large right burner would only light in the outside and would not stay on

Ordered the part. Received the box damaged and did not realize the part was damaged until our son came all the way from Columbus Ohio to install it. We ordered another part which came in a timely manner. Even though I reported the problem and told them that we are not very computer literate they still would not accept that the part was damaged until we sent a picture. Our son came back from Columbus to install the new part which took about an hour. He took pictures which I was then able to send. They then asked for a serial number. I had already sent all the numbers from the part but that is when they said they wanted the serial number from the stove. We are elderly and getting that required me getting on my hands and knees to get it near the floor. Luckily I was able to get up. After multiple emails I now have to send the part back. Good luck to anyone working with this company. I will be waiting for them to reimburse me for the defective part.

Parts Used:

Haliant Element - 12 Inch

JoAnne from LAMBERTVILLE, MI
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Wrench set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

drwer slide under stove broke off.

recieved part the next day. looked different but I followed instructions and the part worked perfect.

Parts Used:

REAR SUPPORT

paul from sewell, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

burner not work

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W