JB650DF5WW General Electric Range - Instructions

first remove lower drawer to access 3 1/4” door trim screws. Use nutdriver to remove 3 door trim screws on lower portion of door.
Next, remove 2 door handle screws using small star(torch) wrench..
Carefully install new replacement glass inside outside door trim assembly by removing 2 of the inside door handle assembly screws using 1/4” nutdriver. Then carefully installing glass and reassembling all. Be Patient!! Take your time. This glass panel is extremely fragile!

took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..

I looked everywhere for this part before I came upo9n this site. I found the part from their very well done website. Even had a picture so you could compare to what you have. It was an easy repair. I had been quoted over $200 to repair by a local repair place. Instead it was around $25 and 15 minutes to repair. This is the right site for any part you may need. I have a magnetic card they sent so in the future, if I need anything (and I will !) I can go right to the right place . Thanks also for a very prompt delivery.

Disconnect old burner and reconnect new one

Well I did it all wrong from the get go. I did finally do a search on how to replace it and then it was quite easy. Learn from me, watch video and save yourself tons of hassle.

Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.

Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.

First I determined that the problem was the range element control switch by switching the 2 heating elements of the same size and turned both on to a low setting. With the 2 elements switched the same burner position that wasn't working correctly before I still wasn't working correctly even though I'd switched the heating elements. Then when the new switch arrived I simply switched off the circuit breaker to the range, removed the back panel to the top of the range and the knob on the control switch and replaced the defective switch with the new one and put everything back in place.

Initially replaced the switch on the range--a simple job--pull the wires one by one and place them on the new switch. This did not resolve the problem, which meant that it was the burner, not the switch. I left the new switch in place and ordered a new burner. This, too, was simple, but involved creating a detailed drawing of the switch connectors rather than photos, which, because of the crossing of similarly colored wires, might have been confusing. The only hitch was that the burner is attached to the top by indented clips that fit into pegs at numbered locations on the burner. The clips were very difficult to open and situate, but once done (and this step was the only one where a second person was required) the top was closed and screwed back in place (two screws) and it worked perfectly.

Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.

Watched repair videos on YouTube to prepare. The repair was very easy.

Red Light Off

After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove the swith assembley from the front panel.

I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)

Being a front burner, I used a 24 in piece of wood to hold up range top. After removing to screws holding top. Made note of numbers on old burner and wire locations. Took off wires and three spring clips. Then replaced with new in numbered locations , wires next

Replaced control panel after removing original control panel facing with heat gun and Wala