JB480DM2WW General Electric Range - Instructions

Easy

First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in perfectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.

Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done

after removing element.I order part. part was inserted without problems . It was correct fit. I am now baking again. Thank you the quick services on the order.

popped the new one on!

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next ....awesome

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!

First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.

remove the door, removed about six screws and did a clean up on the glass. the replacement part was screwed back in place. so easy

My oven is wired into the wall so I had to cut the power off at the fuse box. The hardest part was pulling the stove/oven away from the wall to see if it was a simple plug in or wired in. I lifted bottom drawer out so I could get leverage and lifted the entire unit so I could put the front feet on the soft pads. It slid away from the wall easily. I found a socket that fit the screws on the plate holding the broken element and unscrewed it, saving the screws. A gently tug on the element pulled the attached ends through the hole. The tip of the ends were attached to the wall wiring by a small sliding metal clip. I carefully pulled the ends apart. One was hard to get apart to I had to push it with the tip of a knife. Once the old was off the new was super easy to put back on. Side the tips to the clips, screw the plate in place and push the oven back in place. Flip your fuses and turn on the oven. Yeah!

took 5 minutes with a nut driver and son. I had previously watch your video and went exactly as the video described and showed.