JB400DP5WW General Electric Range - Instructions

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.

threw out the old ones and slide in the replacement ones from you.

Performed repair using a video for reference.

1st replacement part was damaged from Shipping.
Parts Select sent a new one that i received in only a few days.
our stove is slid into a granite island so the disassembly was not as simple as most. It was necessary to remove the controls, the controls housing & screws along the top of the oven door.
Within an hour the stove was back in place and working perfectly.
Great service from Parts Select

Troubleshot the problem, found the SWITCH ROCKER was seized up,
Removed the rear inspection panel, and saw the installation procedure.
Called Part Select and discussed the problem.
Gentleman quickly found the part and we ordered it,
Pulled the existing failed switch out, replace the new switch, done.
Saved at least $100.00 by not having and appliance company do a simple job!
This not the first time Parts Select has satisfied my needs and importance of saving hard earned money.

Sincerely
Satisfied customer
Edward P. Mike

Took me a second to remember that YouTube is just as handy a tool as what I've got in my toolbox. The installation of the new glass was as easy as apple pie. Anybody that has ever used a screwdriver could manage that fix and do so single handedly. PartSelect.com came through with an easy-to-navigate website, a very reasonable price range and anything you could ask for to help fix whatever has broken. I quoted a gentleman in my town, a handyman, and he came back with a price tag of over $300 for parts and labor! Even with tax, shipping and the new glass I came in well under $100, and the labor was next to nothing. If i ever have to replace or fix something in my house again, I'll be using them, Without a doubt. Thanks for everything, dudes. Cheers!

recieved part the next day. looked different but I followed instructions and the part worked perfect.

Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.

Followed the directions!

replaced lights in refrigirator and freezer

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

Easy removal of switch and installation of new switch block.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.