All Installation Instructions for General Electric Range JB255DJ2BB

Terminal block connectors worn out wasn’t making a good connection with the stove top burner

Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.

Parts Used:

Surface Burner Terminal Block Kit

Lance from HAHIRA, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven could not be turned off once settings were turned on except by unplugging hookup.

Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.

Parts Used:

CONTROL OVEN TO9

Charles from BENNETTSVILLE, SC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burner spontaneously cycled without knob activation

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Anil from Milpitas, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

My electronic control board went out so I could not use my oven. My oven light blew as well.

I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.

Parts Used:

CONTROL OVEN TO9

Light Bulb - 40W

Stella from PADUCAH, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Could not adjust heat on burner.

Followed directions given by previous customers problems which we found on the internet.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

Roy from Au Gres, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Element blew hole in self then no power to burner.

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Melvin from Portland, TN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

temperature sensor went

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Parts Used:

Temperature Sensor Kit

Alex R from Randoff, NJ
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven would not heat up

I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.

Parts Used:

Bake Element

MICHAEL from MORROW, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

control switch had stopped working, burner wouldn't work properly

took out a couple of screws and replaced with new switch, plugged in switch wires. very easy

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

Ruth from JACKSON, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

My burner trays were worn out and I needed new ones

I simply pulled the old ones out and replaced them with the new ones. It looks so much better and cleanes up well.

Parts Used:

Burner Bowl - 8 Inch

Burner Bowl - 6 Inch

Mary Jane from La Junta, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven board went out

One wire at at time then used my razor blade to get front off stuck right back on

Parts Used:

CONTROL OVEN TO9

Jackie from TICKFAW, LA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broiler Unit Failed

Used nut driver and removed the 4 nuts holding the broiler. Pulled electrical wires of old broiler Received new unit and it was just as easy to replace. Thank you for assistance.

Parts Used: