J2S968SH5SS General Electric Range - Instructions

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.

First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the back top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!

put it in but it keeps falling out. they're made narrower than my oven grate.

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

plug in thermistor when needed

The actual repair was relatively easy but access to the area in the oven made it a little difficult. Just unscrew 5 screws with a nut driver, unplug the old element, plug in the new element and reinstall the 5 screws. The only thing that made this repair difficult was being able to reach the connectors where you plug in the new element. They are loose wire connectors that don't reach very far out of the element receptacle. It was difficult to hold the end of the connector and plug in the new element because the oven door is in your way. Maybe it is easier if you take the oven door off first?

Shut the power off at the electric box.Disconnected coil from roof clips.Pulled wire connection from back wall. Disconnected wire clips, connected new unit.Clipped to roof and turned on" Working fine".

Replaced burner gaskets.

I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.

turned oven off, pulled oven out from wall, removed back of oven, unscrewed sensor from oven replaced with new sensor, put back on, turned power to oven on, tried oven at 425, my temp. gage and the oven temp matched. a very easy fix.

pull out defective seal with pliers clean area and press new seal into place making sure the spring clips on seal are completely inserted into door slots push ends of seal into holes in bottom of door

Installed new guides with a nut driver without any problems.

Took about 15 minutes to take the old one off and put the new one on. Not difficult at all.

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."