All Installation Instructions for General Electric Range J2S968KH6CC

Broken drawer support

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Parts Used:

REAR SUPPORT

Mario from Deer Park, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

missing meat thermistor

plug in thermistor when needed

Parts Used:

Meat Probe Thermistor

John R from Asheville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Grate Foot Have 8 For My Stove And One Breaks Every Now And Then

This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.

Parts Used:

Grate Foot

Lee from Kenner, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Missing grate foot.

Ordered by phone parts & very pleased with all of transaction.

Parts Used:

Grate Foot

Barbara J from Sweetwater, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

defective oven door seal

pull out defective seal with pliers clean area and press new seal into place making sure the spring clips on seal are completely inserted into door slots push ends of seal into holes in bottom of door

Parts Used:

Lower Oven Door Gasket

Brenda from Cave Creek, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Stove drawer rear guides broken

Installed new guides with a nut driver without any problems.

Parts Used:

REAR SUPPORT

Robert from Shakopee, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Our bottom drawer support broke and the bottom drawer was canted

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Parts Used:

REAR SUPPORT

Robert from Woodinville, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

gasket replacement

Took about 15 minutes to take the old one off and put the new one on. Not difficult at all.

Parts Used:

Lower Oven Door Gasket

Marilyn from Auburn, WA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

rear drawer supports broke

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Parts Used:

REAR SUPPORT

TERRY from RICHMOND, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Broiler Element Repair

I was attempting to replace the broiler element on the oven, but I discovered that the wiring may be the actual problem. I suggest before you order parts for a broiler repair, that you test the wires to ensure that you have continuity. I will have to trace the wires back to the source (the other element works fine) and see if I can find the problem with the current. I will keep the broiler element I ordered until I can confirm that the old element works.

Parts Used:

Broil Element

Robert from SANTA MARIA, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Broiler heating element was not working

Turned off the circuit breaker. Removed 5 screws. Unplugged the heating element and then plugged in the new one and replaced the 5 screws. Very simple.

Parts Used:

Broil Element

Jim from Hyrum, UT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Hard to move drawer in and out because the rear drawer supports broke off.

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

Parts Used:

REAR SUPPORT

Steven from Lansdale, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

oven temp. was not what setting called for

turned oven off, pulled oven out from wall, removed back of oven, unscrewed sensor from oven replaced with new sensor, put back on, turned power to oven on, tried oven at 425, my temp. gage and the oven temp matched. a very easy fix.

Parts Used:

Oven Sensor

John from Acme, WA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver

Was this instruction helpful to you?

Igniters on gas stove were randomly sparking.

Backed off screws that held the burner base over the gas opening. Removed C ring and spring and slid out old igniter, cleaned base, inserted new igniter and replaced burner gasket, refastened base and the job was done. Repeated for other for burners. Easy.

Parts Used: