IVE30100 Inglis Range - Instructions

Terry from Mountain City, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

temp sensor went oven not heating

the hardest part was moving stove to trplace part

Parts Used:

patrick from HUGHESTOWN, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Oven stopped heating, error message stated heating element

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

Parts Used:

Lana from WATERVILLE, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

had for 2 weeks didnot work called for warinty they fixed stoped woking again about 18months later called them got price then bought though you.

first i turned off breaker . then slid out stove .usea cordless screwdriver totake off back then unplug switch then take off knob then take screwes out of front of switch theninstall new one revice method. took me longer to do this then to do the part

Parts Used:

Range Temperature Switch 240v

frank from pittsburg, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

8 of 18 people found this instruction helpful.

Was this instruction helpful to you?

The oven was blowing a circuit.

Unplugged unit from wall.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.

Parts Used:

Rhonda from Logan, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Oven Temp inaccurate

I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!

Parts Used:

David from BURNSVILLE, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.

This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.

Parts Used:

George from Irving, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

oven not keeping correct temp and sometimes would not relight when temp went dropped.t

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

Parts Used:

Gary from PLUM CITY, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Bake element was broken

Remove the old part and install the new part.

Parts Used:

Range Screw (Grnd Wire / Back)

Alexander from LINCOLN, NE
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bottom element stopped working

Unplug the stove from outlet so no power going to appliance. Had to use wd on screws to help loosen
Little bit of effort to loosen. Took new element from package. Replaced screws just tight donot over tighten. Plug stove into outlet turned on. Did a automatic clean. Oven clean and baked cake later I am back in business and 63 years. Was quote 240.00 to from a local repair person. When using wd make sure you wipe any drip from before turning on oven.

Parts Used:

ArLinda from ALTON, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Drip pans were not original to range, I could not get them clean.

I reoved old drip pans and installed new ones. Very easy, they look great!

Parts Used:

Lynn from BRADENTON, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Heating element, broken

Unplugged appliance, removed the 2 screws that mount element. Unhooked the electric wires,with pliers.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.

Parts Used:

Frank from COLUMBIA, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Old lower element fell apart

1. Unplug the power
2. Unscrew the two screws that hold the element
3. Pull the element out a little to expose the wires.
4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN.
5. Firmly seat wires back onto new element and replace screws
6. Bake stuff!

Parts Used:

Matthew from MIDDLETOWN, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

replaced old drip pans

Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!

Parts Used: