All Installation Instructions for Whirlpool Dishwasher IUD7070DS2

The filter came out and pushed the arm up on the burner and melted it.

The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.

Parts Used:

Dishwasher Lower Spray Arm

Sherry from SUSANVILLE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Split tine row

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

Parts Used:

Tine Row

Janet from MIDDLEBORO, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The old filter was warped, allowing food into the sprayer system

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

Parts Used:

Screen

George from LYMAN, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher not draining

Very easy to twist off the old pump and replace with new part. Worked perfect after replacement! We just followed you tube instructions

Parts Used:

Dishwasher Drain Pump

Tina from BLOOMINGTON, IN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher door stopped latching properly.

Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.

The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.

Parts Used:

Door Latch - Black

Bryca from TULSA, OK
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Friction sleeve came apart ....would not hold door in place

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

Parts Used:

Dishwasher Friction Sleeve

Gary from WAUKEE, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

it was the detergent dispencer, we had to install it twice. and it still does not work

like the instructions showed

Parts Used:

Dispenser

Sharon from ALTOONA, IA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher door drops quickly to wide open position when unlatched

Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.

Open dishwasher door.

Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.

Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.

Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.

Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.

Repeat for right side of door.

Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.

Slide the dishwasher back to the original position under the counter top.

Insert the screws in the top brackets to secure the dishwasher.

Parts Used:

Dishwasher Friction Sleeve

Gene from BATON ROUGE, LA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Part in the lower rack had rusted out

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

Parts Used:

Tine Row

Janet from Hollister, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher wasn’t getting water.

I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.

Parts Used:

Dishwasher INLET VALVE

Kevin from MILLBURY, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Poor to no cleaning lower basket

lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.

Parts Used:

Dishwasher Lower Spray Arm

jeffrey from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replace black access panel on Whirlpool dishwasher (model WDF520PADM7)

I needed to replace the black access panel on my Whirlpool dishwasher (model WDF520PADM7).

By following the instructions in this short video (https://www.youtube.com/watch?v=995mtdO7rQg) , I was able to complete the replacement in under 10 minutes. You'll need a flat-blade screwdriver. The Retainer Clip - Black can be a little tricky to position into the opening, so have patience.

Keep in mind that the Retainer Clip - Black only contains ONE clip and so you must make sure to order TWO Retainer Clip - Black from PartSelect.

Parts Used: