All Installation Instructions for Inglis Range IRP85800

Element had burned out, and the drawer glides were broken .

Replaced both .

Parts Used:

Oven Bake Element

Range Rear Drawer Glide

Allen from ASHLAND, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven Elementwas burnt into

Watched the video and did as shown

Parts Used:

Oven Bake Element

Fred from APACHE JCT, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Rear drawer slide was broken.

Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.

Parts Used:

Range Rear Drawer Glide

David from Mauldin, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

baking element non operational

removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!

Parts Used:

Oven Bake Element

GARY from JACKSON, WY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven Demon Possession

Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.

Parts Used:

Broil Element

Kevin from Greensboro, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Clothes would not fully dry in automatic cycle

1st gen whirlpool Duet dryer sensor not working in automatic cycle.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.

Parts Used:

Range Door Hinge Left Or Right Side

Robert from WALDORF, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Worn/Bulb Socket

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Parts Used:

SOCKT-LITE

JOSEPH from COON RAPIDS, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

slides on lower drawer were broken

I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.

Parts Used:

Range Rear Drawer Glide

Leona R from Louisville, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Broken drawer glide

Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.

Parts Used:

Range Rear Drawer Glide

karen from Thornton, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Burned out burnrr

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

Parts Used:

Element with Limiter 6 Inch - 1200W

Rita from COOPERSBURG, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Dual Surface Element went out

Followed the instructions in the video provided by PartSelect, which was very accurate. They only problem I have encountered is that the wiring from the old element compared to the new element do not match up 100%. I had to call Whirlpool today and schedule a Tech to come out and see if they can resolve the problem. Right now, when the burner is turned on, both the inner and outer elements turn on.

Parts Used:

Dual Surface Element - 2500w/1200w

Larry from RADCLIFF, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

bad burner

My dual zone burner would trip my breaker anytime i tried to turn it on. All the other burners would work fine. I searched online and found a way to test my burner, which was shorted or grounded out. I purchased a new burner from the site...It was as cheap or cheaper than other sites. It showed up a few days quicker than i was expecting..I also replaced the switch to the burner, just as a precaution and to save time since i already had the top glass off of my burners....EASY JOB!

Parts Used:

Dual Surface Element - 2500w/1200w