IP44001 Inglis Washer - Instructions

I basically dismantled the washer and turned the washer over to access the motor,transmission and pump.I disconnected the electrical connections first.I then released the clips for the pump and the clips for the transmission.The coupler was broken in little pieces.I went to Google to search for parts and happened to reach your Web Site.I found the part number for the coupler from the schematic and ordered it.It was then I discovered the part number for the cam dogs for the agitator so I ordered it also.While on you site I read the various troubleshooting stories and how each was repaired.I put myself through a lot of unnecessary work by dismantling the whole washer when all I had to do was turn it over and access it from the bottom.The parts arrived in three days and the install was rather simple thanks to the direction of your site.I had a heck of a time reassembling the washer but all in all $42.00 was a lot cheaper than a repairman or a new washer.We now have a working washer and no leaks.
Thanks to your site ,I have a happy wife and clean clothes.

First I went to the Whirlpool site and downloaded the illustrated parts list for this model (a PDF file).

Seeing the part number, I then ordered the part from PartSelect.com.

While waiting for the part I tried to research how to remove the timer knob, but none of the online help I found was correct- the knob does not unscrew, but is held in place by a black plastic "keeper" on the back of the timer. The removal instructions are printed on the timer.

When the timer arrived I unscrewed the 2 screws at the back and edge of the console panel. Then the panel lifts up and out, exposing the timer. I released the knob, then removed a small screw beneath the knob that holds the timer.

Then I unplugged the wiring harness from the timer and removed it. I then reversed these procedures and installed the new timer.

As it turned out, the problem was not with the timer at all, but rather a defective lid switch, which is also located under the console panel.

Once I replaced the lid switch (very easy), the washer worked perfectly again.

Despite my imperfect initial diagnosis, a very satisfying experience.

Thanks for the great service.

Rick

1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamps.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]

before ordering the parts, I pulled the cap of the agitator, removed some internal parts of the agitator - had to remove one hex head bolt, and noticed the threads on the 3 little teenie weenie plastic dogs were worn off. I bought the repair kit on line after entering the model number, parts were here in a few days, and the repair took about 15 minutes. Works like new again.

The directions provided with the parts were very clear and made the job quick, easy, and painless.

Three of the four agitator cogs had broken. The agitator was able to spin freely both clockwise encounter clockwise which it should not be doing. I replaced the cogs as well as a couple additional parts just to be sure but the cogs were the important one. Very easy.

Put the machine on its side. Remove old hoses and screw new ones into place. Done in under 20 minutes.

Removed bolt holding top of agitator, removed top of agitator. Replaced parts. Reinstalled agitator. An old machine now works like a new model.

First, I'm so excited that this site exists because I knew that the problem was minor and I didn't want to pay the outrageous housecall price of a repairman. I read other customers' experiences on how they fixed the problem and that made it sooo easy! Basically unscrewed the screws on the far left and right on the top panel, folded it down toward front, unscrewed and unplugged the ground wire and replaced the part. Someone else had warned that the lid should be open to remove it and that was a huge time-saver. Thanks so much! The part was broken because of very poor design. The part actually worked fine, but the piece of thin plastic that held the part in place broke. Back to the drawing board Whirlpool.

I had to take the motor and transmission out. They are one piece. Removed the clutch, take off trans. cover, remove a snap ring, take the striped gear off, and put the new one on. Then put put everything back on the way it came off.

I had a little difficulty at first, trying to remove the back of the unit. I then figured out that the repair was to be made by leaning the washer back and removing it from underneath. That became really easy as the bottom is open.I had to remove one nut and then the agitator from inside, then tilt the machine back, disconnect the two hoses from the pump, remove three bolts and lower the motor/ transmission assembly. Then I had to disconnect the motor from the pump ( with two snap on clips) and remove the broken plastic coupling. The new coupling had a metal insert that seems to make it stronger than the original piece.I then just reversed the procedure to put it together again and it worked fine. The part was shipped immediately and I got it sooner than I expected so I greatly appreciate that. Overall it went well, and by the way, it was my daughters washer and she was happy as well.Thanks, Roger

Read the directions in the repair kit first- a 7/16" socket and 10" extension is needed. Assembled new dogs on agitator "cup" and retainer, added marine(waterproof) grease to assembly washer, replaced bolt anyway and installed new o ring. Took less than 15 minutes-READ ALL DIRECTIONS FIRST!

I thought the click of the lid switch sounded different so I pulled the top console and tested it for continuity in both positions and found none. When I by-passed the switch the washer started up, so I knew what the problem was. There are four screws involved to remove the console which reveals the lid switch to the left side. There's a single screw for a ground wire but the switch itself is simply snapped in place after disconnecting the wire harness plug (must be done with the lid open btw).

I was lucky to diagnose the problem accurately so that the first thing I suspected turned out to be the problem!

First off unplug the machine then turned off H/C water supply and removed hoses, laid the machine on its side, removed 3 motor supp. bolts, loosened drum pulled out shaft and clutch assembly was right there. Also replaced coupling while it was apart. And to think, a svce company wanted 179.00 just to walk in my door and diagnose the pblm. Then, parts and labor were extra. Thanks for the help/advice, piece of cake!!!!!!!

Laid washer on front side and removed top spring, then lifted the tub assembly to replace the right side spring, the one behind the motor was the hardest, I lifted the tub then removed the spring bracket at the tub with pliers and a socket. The top seal all I had to do was take the 4 screws that hold the top on (it takes a long extension) then sit it bak up and I lifted the top up to give me enough room to unsnap the top piece of the tub, cleaned it up put seal in. The parts fit perfitlt and real fast shipping, I bookmarked the site and will buy from again. JIM

First I removed the top of the agitator and then used a socket and ratchet to unscrew the bolt and put the new one on and tightened up the bolt, real easy.