IMS106 (BY09A) Maytag Ice Maker - Instructions

Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness

Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on

ALL FIXED!

to easy to describe, remove 3 screws and a wire plug then install new unite.
Works great
Thanks

remove 3 screws,rotate assembly,depress lock on wire harnass connector,un plug harnass.remove old assembly,remove and transfer side cover and steel wire at front of assembly,connect harnass to new assembly,rotate into place,aling screw holes and install 3 screws.flip front steel wire down and wait for about 1 hour,first tray of ice will fall..all done.

As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.

Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.

I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.

Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.

Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)

Old ice maker leaking water and produced ice cubes with black inclusions. First, I removed old ice maker per video instructions. Transferred electrical cable, cover, and bail to new ice maker. First installation failed because I failed to make sure water tube correctly enter back of ice maker. No ice. Initially thought electrical cable wasn't firmly in place. Then I noticed frozen water dripping down back of freezer. A clue! Removed ice maker and reinstalled making sure water tube went through the hole in back of ice maker. Now the new ice maker works beautifully!

Just kept working on it.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

Repair done according to video and instructions. What you need to know is myself and my husband are adverse to all kinds of "simple" repairs because they never go well and we are not handyman kind of persons. This, I must say, was a delightful change in our typical experience of attempting to make our own repairs.
Thanks
Sandy

Removed top drawer from freezer. Unplugged the ice maker. Uncrewed the bottom screw. Loosened the two top screws. Removed old ice maker. Removed all the parts that didn't come with the new ice maker and installed on new ice maker. Reinstalled the new ice maker. Started making ice with no leaks in about 3 hours.

Adding water to Ice Maker, caused ice to be made. I assumed the Single Outlet Water Valve to be problem (despite %4 probability). I suppose problem could have been in the ice maker itself and it's interface to the Single Outlet Water Valve but fortunately the Single Outlet Water Valve solved the problem. The Parts Select replacement part video was very helpful and the replacement was fairly easy. Were the problem in the Ice Maker itself, I don't know that I could have justified the cost of the the repair for a 17 year old refrigerator.

I have a Maytag Refridgerator with lower freezer and ice maker. Stopped making ice. Noticed the unit would fill up and freeze but the tray wouldn't rotate to drop the cubes into the tray. Cleared the frozen trays to see if it was just stuck but same thing happened. Replaced unit, not difficult with the exception that the top tray is ridiculously hard to get out. Never did do it, just worked around it. Working perfect now.