IKU58660 Inglis Dishwasher - Instructions

after that every thing went very well

Pulled dishwasher out from counter. Took cover off and replaced door springs.

I follow the video and it was easy thanks! you save me money and my old dishwasher Timmy S. GA

Open the dishwasher door and remove the lower dish rack.
The spray arm nut had broken off and the spray arm was wobbly.
Removed the spray arm. The threads of the nut had broken off inside the arm. I used three 1/4 inch bolts and inserted them together inside the threaded part of nut and turned counterclockwise. The threaded section came out.
Once the new nut arrived, I replaced the spray arm in the dishwasher and screwed the new nut clockwise in the center of the arm. That's it!

just put the pieces where they belonged and tighten the screws. it longer to figure out how it was supposed to fit than the actual fixing.

It was very simple, the repair took less than 5 minutes start to finish. I removed the top dish rack, took out two screws and the broken part slipped right off the water feed tube. I slipped the new upper wash assembly on the end of the tube and replaced one screw. My dishwasher is an older model and the new part only has a hole for one screw but I cannot tell any difference in stability or performance. I put the top rack back on and the dishwasher is as good as before.

used a screw driver, removed 2 screws, removed broken piece, screwed in new part ....all done :)
took less than 15 minutes to do*

i just wanted to let everyone know..I ordered the part on a monday and received it on wednesday I was amazed...the part fit perfectly ...and was very easy to install myself....ty so much ...

First I removed the nut holding down the lower washarm in place. I then lifted up the lower washarm where it's held in place by the nut. I replaced the two new parts: The lower sprayarm seal that seats underneath the lower washarm and the washarm bearing ring that seats on the top of the lower washarm just underneath the nut. A schematic parts list diagram can be downloaded on the KitchenAid website. The wobbling motion of the lower washarm still seems to have the same amount of play as it had before I replaced the two parts. The lower washarm itself is in fine shape including the nut. I even attempted several other different ways to install the seal and bearing ring, yet the washarm still wobbles when I manually spin it. I called KitchenAid to find out if wobbling of the lower washarm was normal. Unfortunately, the person I spoke to didn't seem to me to knowledgable enough in this area.

I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.

Simple easy twist on and off replacement.

Removed spray bar by removing the plastic finger thumb screw and replace as shown by you web page. Very simple.

My model dishwasher was a bit older. The new replacement top upper wash assembly had a slightly different construction but was a perfect fit. It even has added protection of the spinner by adding two little fingers around the spinning wheel to protect it from being knocked off by dishes, the most probable cause of its damage to begin with. Only minor issue was that my old unit had 2 screws/holes to mount it and the new replacement unit only came with 1 hole pre-drilled. But if your doing this yourself, you probably have a drill and some small bits somewhere, so a few minutes extra and you'll have an exact replacement unit. Total time took less then 10 minutes and my unit was as good as the day I brought it. Good buy!

Detached lower wash arm and replaced bearing.
5 minute fix.

Simple,removed broken part and replaced with new part.Piece of cake, Took two mins.
I can't get over how fast the part was received.I am sold on "PartSelect"

Removed the center screw in, then the wash arm, removed the old seal and replaced it with the new one, replaced the wash arm then the screw in, and was done and ready to try it out.