IHP33801 Inglis Range - Instructions

Instructions on line were very helpful. The only problem was getting the screws loose on the clamps that held the glass in. If I was going to redesign this door I would use Hex head screws that can be removed with a nut driver. Most of the time for the job was taken up by cleaning off accumulated grease. You will be surprised how much gunk can get inside the door.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Had to screw off old terminal block & screw on new one

New electric stove was out of my price range. I ordered one electric burner and 3 drip bowls. looked at part select instructions and repaired 2 that didn't work. Now next month I'll order one more part to fire up the last burner. Also following their clear instructions and I'll have a full working electric stove for a little over 100.00 dollars, as opposed to a new one at over 900.00.Thank you for your help.

The part came in 2 days even though I chose the least expensive shipping method. The hardest part was unscrewing the old screws that held the old bake element in place. We soaked them in WD40, and after a while were able to unscrew them. The new element slid in place and works just fine.

I watched some videos on YouTube first that said you could flip a latch on the door hinges and remove the door entirely. On this older oven there was no latch, you just open the door to its first position and lift up and out to remove the door. Unlike newer doors leave this one face up on a table to work on it. Remove all (10?) of the screws along the bottom edge, pull away the side door trim pieces, then remove the outside panel of the door by lifting slightly then pulling downwards. Mine was actually a glass panel, so be careful. Remove the two screws holding the upper door trim down onto the hinge mechanisms and rotate the trim out of the way. Lift off the large metal cover to expose the first, outer glass, then remove the insulation, then remove the screws and clips holding down the metal frame around the inner glass. Clean everything well (I used a baking soda paste), then replace in the reverse order.

Replaced both rollers....Quick and Easy!!

The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

TURNED OFF THE POWER TO THE RANGE, DISCONNECTED THE ELECTRIC PLUG. I unscrewed the element attached to the oven, disconnected the connectors. Reconnected the element and screwed the part back to the oven. EASIER THEN I THROUGHT.

removed the screws that secured the lower element. Disconnected the old element from wire contacts. Inserted the new element into the wire contacts.

Remove two screws. Plug n play.

I very simply replaced the gasket where it belonged and I was good to go!

Turned breaker off. Removed oven door for access, two screws loosened element, unplugged wires from element & removed element. Reverse order to install. Perfect fit. Thanks.