HTWP1400F0WW Hotpoint Washer - Instructions

order the part and replaced it and it works just great! May I add never before have I had such an amazing experience in dealing with your company, your company shows pictures and I ordered the part in the late afternoon and I had it the next day, the diagram you show on your site was so helpful, you told us that the part now is replaced with a different #. Once again KUDOS!! to your co.

Followed the video with one exception. The hose clamps were the spring-loaded type and putting the back hose clamp on was a problem, so I substituted a nut driven hose clamp. Other than that, no problems.

removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.

It was hard for me. I'm a 54 year old woman. I tied it to the wheel with twine. It kept popping off, right it the time I would just about have it on. Several times !!!! I had no zip ties. Finally I tied the part of the craft stick on tightly. Put the belt on the motor rod and as much of the wheel as it would allow. Started turning slowly. There's really no room. I finally wiped it. There was one time that I sounded like the man off the movie Christmas Story. My youngest daughter is 13. She started laughing. It wasn't easy but I BLESS GOD for it. Thank all of you so much. Be safe and take care.

As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.

Removed front with putty knife to unlock hinge.removed and checked pump removed hose clamps with wrench and nut driver replaced hose reverse procedure

First tried pulling the old agitator out by hand but couldn't get my fingers under it to pull upward. Tried several times but no success. Finally put two metal rods about 8 inches long in the holes in the bottom of the agitator and used them to lift upward, it came up immediately. I then pushed the new agitator down into the slot and it was finished. There is always a way when you think about it.you are a winner.

The repair was done like the video suggested to do and in the order. And it worked well.In the step by step procedure.

after reading repair stories, decided I should take front panel off and see where leak was coming from. taking the panel off was real pain but well worth as inside was dry! so I looked again and discovered a pin hole in drain hose that only leaked when tub was full. while I had panel off I noticed tub dampening straps were broken so went ahead and ordered those parts too.

Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.

Remove screws from rear top panel. Remove 2 retainer screws for instrument panel. Pull panel forward and then lean forward. Remove electrical connections. Remove screw that retains module. Pull know for selector outward . Push retainer clip out using screwdriver. Remove know. Tap shaft to pop module out . Replace module and installation is reverse of removal

really easy repair, just open the front cover panel & removed the Drain Pump.

Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.

pulled up on agitator and it came off and replaced it with the new one

The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.