HTS18CBMDRWW Hotpoint Refrigerator - Instructions

No problem, had the job done in twenty minutes,Thanks John

My wife and I followed the installation video & put the gasket in hot water. We struggled to get it started in the second corner on top. Gasket had cooled down so wasn't wanting to go in the slot. I finally got the bright idea to use a hair dryer to warm the gasket as we pushed it along.
That helped us finish the installation.
Not sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator!
My newer refrigerator "snaps" shut.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Removed the back of the freezer, 4 screws, and then unscrewed the motor mount with fan and motor attached. Switched fan blades to new motor. Reinstalled motor mounting then back of freezer. I had to go buy the ring opener tool at the auto parts store. $12.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Followed the video by Parts select. Very accurate to remove and replace. The only trouble I ran into was getting the clip back onto the fan blade shaft! Have to improvise and use a wirenut to spread it and it went right onto the shaft. Now working perfectly! Thanks for the video and the fast part service shipping...

I followed the video instructions and the job was done in no time at all

Turn off refrigerator. Remove the plastic air flow cover, styrofoam channel and metal panel inside freezer compartment, remove hex nuts holding motor mount, unplug connector, remove old grommets, remove compression ring, (note 1/4 inch extension of shaft through fan) carefully pull fan blade off motor shaft and put on new motor shaft, leaving 1/4 inch of shaft extending through, replace compression ring. If your new fan motor has a female snap connector and the old motor has a male connector (as mine did) you will have to cut the wires on both new and old motors, splice and solder the male connector onto the wires of new motor, wrap carefully with premium electrical tape (or shrink tubing). Replace the 2 grommets, Reconnect the fan and bolt back into place. Make sure all the bolts around the mount are tight. Replace the metal panel. Manually spin the fan making sure it is free of the shroud. If it binds in the shroud, physically move the motor and mount till it rotates freely. Turn on refrigerator and test fan operation. If it's all good, replace the styrofoam and plastic cover.

The is my 'refreshment' cooler and sits in our garage. Hotter than heck in the summer so the things runs a lot. Started making a little growling noise. Had to partially disassemble the back panel to get to the fan. Touched the exposed shaft for a second and the sound stopped. OK, it's the fan. Went on line, used the (really great) exploded diagram to figure out what I needed. A couple days later the parts show up. Installed the new fan blade and retainer Removed the old motor (couple of mounting screws), connected the new motor (a plug in) and mounted the new motor making sure the grommet on the front and back were engaged. Turned the unit on and everything worked. Reinstalled the foam channel, the back panel and it ran perfectly. Great support (the diagram), fast delivery and fair pricing. Not bad!

it was so easy to replace the part and good experience I love when I can trouble shoot and fix the problem

per your instructions

As explained on your how to on the web. Ordered by phone ---A1--Arrived as promised-- The kind of service we used to expect.

the hardest part for me was the fan blade clasp.still only took like 20 minutes.But the best part was, the part was delivered and fixed within 24 hours of buying online. Great service guy's, Thanks.

Bought the part and did it. Super easy with any kind of mechanical ability. It took 18 minutes from start to finish, I think it took longer to clean out the freezer section and restock it, than the actual job did.

I watched your Video. Thank you.