HMG901480 Admiral Ice Maker - Instructions

First I removed the screw holding the ice maker on the wall and then loosen two other screws in oreder to remove the maker. Once out, I replaced the maker with the new one. Then replaced it in the refrig.

Unplug fridge, close off water supply valve. Remove two screws attaching assembly to freezer wall, detach wiring harness. Remove parts from old assembly: wiring harness, shut-off rod, harness clamp and attach to new assembly. Connect wiring harness, two screws attach new assembly to freezer wall. Plug in fridge and open water supply valve (after an opportunity to change in-line filter). Works now!

Piece of cake. Removed two screws, pivoted old ice make up, lifted it out of the mounts. Installing the new one was just the reverse.

Identifying the correct replacement ice make was easy also, due to the photographs on PartsSelect.com

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

First, unplug power to Fridge, then remove ice bin and set to one side, then remove the clip that holds the fill tube down by pulling up on it, and remove the fill tube. Remove the two top screws on ice maker assembly first, as the bottom screw will support unit. Then remove the single bottom screw. Rotate the Ice Maker slightly down and this will expose the electrical connector. With a short, small, flat head screwdriver in your left hand, depress the locking tab for the connector, while your right hand supports the assembly and pulls the connector outward to disconnect. Remove old Ice Maker, and remove the bin full lift wire, it's a slide in fit and install in your new unit. Check your fill tube water diverter on the right side of Ice Maker unit , you may need to remove the blank, it is U shaped and molded for easy removal, but use caution when removing to be on the safe side, this allows the fill tube to go down into the diverter, Re-Assemble in reverse order. Give the unit plenty of time to reach proper operating temp, and cycle. Make sure and discard your first Ice cycle.

First i removed the three screws that held the assembly to the fridge, then removed the water flow tube from ice maker. 2- flipped ice maker over ,then used a small flathead to push in locking tab that held wire harness and out comes ice maker. All though the water cup was not quite the same i used the old ice maker to take apart to see how it was put together,hopeing there wasn't a myriad of parts. -NO INSTRUCTIONS- piece of cake, don't take out outside screws,take out the 2 inside screws-these srcews hold the guts to the water tray-pull apart and reassemble the unit after you have switched the cups. then reinstall into fridge with your outside cover and the full bin wire and your done. It helps to be alittle mechanicly inclined. -NO GUTS NO GLORY,DONT BE AFFRAID TO LOOK OUTSIDE THE BOX-

I took the screws out holding old old ice maker, unpluged the electrical socket and old unit came right out. All I had to do then was plug electrical socket into new icemaker place unit in position and put the one screw back in the held it in place. Plug frig and and it filled with water in about 15 minutes and started making ice. Part was a exact match to the one I removed.

I removed the old icemaker, took it out to my shop & removed the wiring and etc. and put it back in place.

Most of the stories on repairing this ice maker indicated that was real easy until describing the Amana version. The fill tube attaches differently. The recommendation was to use your old "cup". I have found that to make the change required that you find a philips screw driver and locate two access holes in the motor end of the control unit. you can loosen those two screws (they won't fall out) all of the way and pull the control unit from the tray part of the ice maker. DON'T remove the three screws that hold the control unit together or rotate the sprocket. This will allow you to disassemble the parts that hold the "cup" in place. Just remember "if it isn't coming apart easily your not doing it right".

Ordered new part by the numbers and pics. and installation was so easy. I thank you very much

First I loosened 2 phillips head screws at the top of the ice maker (the one that is close to the front is a little difficult to get a screwdriver on). These 2 screws do not have to be removed. Took 1 screw out of the L-bracket at the bottom of the ice maker. I then slipped the icemaker upward from the 2 top screws and unplugged the electrical wires at the connector at back of the refrigerator to remove the ice maker. I then removed the front cover from it and placed it on the replacement ice maker. I also swapped the L-brackets on the two ice makers as the new one was bent. I then reinstalled the new Ice maker in the reverse order.

I simply removed 3 nut head screews and the old unit came off. I removed the ice level arm off the old unit and put on the new one. I removed the old wire harness and plugged into the new unit. I mounted the new unit, plugged it in and was done. I had ice in less than an hour. So simple my 11 year old could have done it without help.

I opened the box, unwrapped the new ice pan, gave it a cursory rinse, and put it in the freezer.

used 1/4 inch wrench to remove bottom screw
and loosend tip screw and removed valve wires and water line

Ice maker was leaking water into the bin causing it to freeze together. To repair I purchased a new Ice Maker part no PS2121513 for $101.00. I used the repair video to find out how to replace the part, the video was very helpful and enabled me to replace the ice maker in under 30 minutes. Once the new part was installed I waited 2 hours for it to start making ice, before the ice maker can operate the bi metal thermostat has to reach approx 14 degrees F. This can take longer than an hour so you have to be patient. I checked mine with a volt meter probes inserted in the T and H test points on the front of the timer assembly. If you read a voltage of 110/120 volts it means the thermostat has not closed. If it takes more than 4 hours it could mean a bad connection so turn off the power and recheck the plug in harness connections. If you do not have a meter you can feel behind the timer with your fingers to see if the ice maker cup or bowl has water or ice in it. Turn off the power first.