All Installation Instructions for Jenn-Air Range H1500PRW

Sockets for the burner elementss were burned out

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

Parts Used:

Surface Burner Receptacle Kit

Martin from Manchester, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Electrical receptacle for burner was defective.

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

Parts Used:

Surface Burner Receptacle Kit

gerald from Hillsboro, TN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

one of wire melted and broken off from receptacle

Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.

Parts Used:

Surface Burner Receptacle Kit

Young from Cordova, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Old surface element burned out.

I ordered and received the replacement element, then unplugged the old one and plugged in the new one.

Job done.

Parts Used:

Economy Y-frame Surface Unit - 8"

Royce from Rio Rancho, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

My heating element stopped working properly and one day just make a pop and stopped working altogether.

I followed the advice givin on the parts select website - it made it totally easy.

Parts Used:

Bake Element

David from San Francisco, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 6 people found this instruction helpful.

Was this instruction helpful to you?

missing one oven rack

put it on, perfect

Parts Used:

Oven Rack

Ana from Riverside, RI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Two old Surface Burner Receptacles needed to be replaced.

I followed the instructions given on your great site. Thank you so much.

Parts Used:

Drip Bowl - 6 Inch

Chrome Drip Bowl - 8 inch

Surface Burner Receptacle Kit

Willis from Anaheim, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

surface burner stopped working. Was not heating up.

The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)

Parts Used:

Surface Burner Receptacle Kit

timothy from south bend, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

heating coils would not work

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

Parts Used:

Surface Burner Receptacle Kit

Adam from Kempner, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Burners quit working

Bought two new replacement burners,they work great!

Parts Used:

Economy Y-frame Surface Unit - 6"

Economy Y-frame Surface Unit - 8"

Brenda from Brazoria, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Elements did not fit properly.

Ordered the parts, installed.

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Economy Y-frame Surface Unit - 6"

Economy Y-frame Surface Unit - 8"

myrna from homestead, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

replace the cook stove's drip bowls instead of cleaning them

I removed the burners and then the older drip bowls of the cook stove--and then I put on the new drip bowls and put back on the burners. My mechanical skills were sufficient for the replacement of the drip bowls.

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch