GZS22IMNWHES General Electric Refrigerator - Instructions

I replaced defrost sets, door gasket but still ice buildup freezer part.

The allan wrench pushes into the holes nder the front control plate and it pops off. Unplug the wires and set aside. Four screws removes the next piece and the "flaper" door is visable.

Cut old tubing in frig with wire cutters and pulled through the bottom wall and removed old tnak from the wall...Installed new tank and ran tubing down trough lower wall and connected to the valve and the freezer door.

The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.

Replacing was easy. Cleaning took the longest. Order screws with parts, I could not find them at the hardware store. I suggest a coat of oil (3 in one) on the solenoid/piston surfaces. I probably did not have to replace them. The rust was inhibiting the piston movement. Some steel wool and oil would have probably fixed it. If the flap closing starts sounding softer, I'm going to take it apart and clean it first.

In preparation, I removed the bottom crispers and shelf to clear space, and removed the hood and items above the tank near the light. You'll need to also move the fridge away from the wall to access the back. Installation seemed very easy - two screws holding the tank itself, one hose to the water supply in the back, and another to the bottom of the freezer door to dispense. Then the hard part started after it was installed. First, I could hear the click but no water was coming out. After several views of youtube videos, I realized there was a plug in the hose to the supply side. Duh! So now I had water, but also a slow drip when drawing water. I believe the issue was that I was not pushing the hose on firmly enough, and eventually I got it right. Also, you need to understand the connector: there is a little ring around the place the hose fits; pushing it TOWARD the housing releases the hose, and pulling it back AWAY locks the hose it place. That was not clear to me without watching a youtube video.

I thought this was my problem as this part causes 90% of the no water issue. However, replacing this part did not fix my problem. I suggest that you test the valve first by disconnecting the water feed from the filter and running the line into a bucket. Once disconnected press the water on the freezer door and see if water comes out.
Other than that, this part is easy to install. Take off the plastic in front of the filter, remover the retaining screws. Remove lower cover in back of the refrigerator, Remove 1 screw securing the valve, remove cover where tubes enter the refrigerator. Take off tubes from valve (be sure to note what is inlet and outlet) and feed back into refrigerator. Be sure to save the putty when the new one is installed.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

I watched the video a couple of times and followed the instructions exactly and the repair was very simple. This repair took me a bit more time than I thought it would just because I followed the steps methodically.

But the video was perfect to guide me through the procedure to replace this part. One of the longest parts was removing the shelving and food storage bins, cleaning them, drying them and then putting them back in after the tank was installed.

Following the advice of others on this site, I popped out the control panel by pushing up through the 2 outer-most holes on the under-side of the panel (the middle hole is unused). I installed the new solenoid exactly as shown in the PartSelect video. The new crank, spring, and flapper installed easily as well; I did apply a little grease to the hinge points on the crank to ensure no binding. I also installed a new microswitch. The wires are best removed from the old switch with a needlenose pliers. The old switch looked like it had some grease on the switch (where it makes contact with the cup lever) so I put some grease on the new switch as well. All-in-all, very easy and the frig works like new. It's nice to hear the flapper slam shut 4 seconds after dispensing ice.

Take the face (the part with the buttons on the outside) off, disconnect wired connectors (three), take the screws out of the part behind that (4), and then find the solenoid value (on the right). It's attached with three screws. Mine was rusted beyond belief. I knew this was the problem, ordered a new solenoid valve, put it back in place with three screws (use new screws that fit, not the old rusty ones if possible). When testing, make sure you give the flap a couple of seconds to close. There is a delay, and I initially wasn't patient enough so I had to disassemble and assemble an extra time because of this.

Simply put: If your solenoid value is rusted and the value won't operate smoothly, order the part and install it. This is as easy as any repair could be.

Ordered new solenoid so the flap would close. That did the trick.

remove the front of were the ice and water comes out
then un scerw 4 scerw and the solenoid slides out unhook the wires and put the new one in

Easy order, fast delivery, two screws, done.

It was so darn easy! Took less then 10 minutes to fix. Self explanatory no instructions needed! Very cool!