All Installation Instructions for Whirlpool Refrigerator GX2SHBXVB07

The center rail was broken

The part just snapped in. super easy.

Parts Used:

Refrigerator Center Crisper Drawer Slide Rail - White

Joella from THE DALLES, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Had to replace the pivot block and vertical rail

Couldn't be easier. Swapped out the old parts with the new. 3 screws total. Perfect fit. Like we have a new fridge now.

Parts Used:

Refrigerator Pivot Block

Refrigerator Vertical Mullion Rail - Black

Myles from BETHLEHEM, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Drawer was cracked and fell apart

Ordered replacement drawer and inserted into the drawer holder

Parts Used:

Deli Pan

Charles from DURYEA, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator would stop cooling intermittently, control panel would not display temp settings until power was reset.

The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one orientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.

Parts Used:

Refrigerator Electronic Control Board

Jim from HALTOM CITY, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

broken right deli drawer guide

Removed old guide and installed new guide

Parts Used:

Refrigerator Deli Drawer Glide

Herbert from MAHOPAC, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

FREEZEING UP

in stalled new circuit board an thermostat an was fixed

Parts Used:

Refrigerator Electronic Control Board

Sherril from ROBBINSVILLE, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Refrig. was not holding proper temp in refrig compartment

Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.

Parts Used:

Refrigerator Electronic Control Board

Dan from Goldens Bridge, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

My refrigerator vegetable bins were sagging when I placed veggies in it.

I came across this site and looked at the diagrams. Instead of buying a new crisper bin frame, I noticed that the crisper bin frame was missing the frame brace. I purchased the frame brace and installed it in the crisper frame, which was easy to push into the slot. This solved my problem. No more sag!!

Parts Used:

Refrigerator Crisper Frame Brace

Lee from SAMMAMISH, WA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator was warm,freezer was cold

Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattaching rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!

Parts Used:

Freezer Evaporator Fan Motor 115v 60hz

Henning from RHINELANDER, WI
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!

I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..

Parts Used:

Refrigerator Electronic Control Board

Marc from SEASIDE, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

ICE BUILD UP AT BOTTOM OF FREEZER

DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.

Parts Used:

Grommet

Gerald from COLORADO SPGS, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The old shelf shattered when we tried to clean it

Just slipped it in. I think it's a very poor design.

Parts Used:

Refrigerator Crisper Glass

Michael from COAL VALLEY, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Right Door Magnet weak, door would not stay firmly closed

Replaced seal on door. Same problem. Went to Lowe's and got several magnetic cabinet door catches. Attached them to the top of the door. (they can be seen sticking up), with the magnet part screwed to the door and the metal plate attached to a small wooden block glued to the top of the body with contact cement. Cost abound $16.

"To infinity and beyond."

Parts Used:

Refrigerator Door Gasket

Larry from CHIRENO, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broke shelf holder hook

This is the small part that is critical to having a fully usable refrigerator but one that no one (even an authorized shop) has in stock. Just pop it back in, and you're done.

Parts Used: