All Installation Instructions for Whirlpool Dishwasher GU2300XTLQ2

No power to dishwasher. Quit mid-cycle.

Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.

Parts Used:

Dishwasher Door Switch

Jon from Bend, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

8 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Drain hose leaking

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

Parts Used:

Drain Hose

Robert from Beaufort, SC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

8 of 12 people found this instruction helpful.

Was this instruction helpful to you?

change front panel

easy as long as you have the right tool to take the panel off, maybe they could include one for people who don't have a good selection of tools. Thankfully we did.

Parts Used:

Exterior Door Panel - Stainless Steel

Joseph from Las Vegas, NV
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

7 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Door spring broke-Door falls down

Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.

Parts Used:

Dishwasher Door Spring

Door Balance Link Kit

Peter from JERICHO, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench set

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Couldn't find the part anywhere, but...

PartSelect found the right part for me on the first try. I had scoured the web looking for this particular drying agent cap. Even Sears said I'd have to order the entire dispenser assembly - $$$!

PartSelect found just the cap I needed at a much better price.

Fantastic service. Shipping was faster than promised. I can't say enough good things about them!

Parts Used:

Dishwasher Dispenser Cap

Brian from Marion, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

9 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher door leaked

Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!

Parts Used:

Door Gasket

Edward from Tucson, AZ
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

old hose possible leakage

put new hose on, very easy.

Parts Used:

Drain Hose

Fred from Kernersville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

8 of 13 people found this instruction helpful.

Was this instruction helpful to you?

the tines in the upper basket of the dishwasher were falling apart

Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.

Parts Used:

Tine Row - Kit of 2

Dorothy from BILLINGS, MT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Noisy rattle in dishwasher since new when it was filling

Remove and replace solinoid, remove and replace mico switch. These are the only two electrically controlled devieces controling water flow. Replacing switch without replacing housing takes a soft touch. A small screw driver helps. Electrical connections have a stay in place nipple. Plyers help get thoes off.

Parts delivered as promised, correct fit. Phone contact available at order question.

Would used this site again.

grade 3.5 A=4

Parts Used:

Dishwasher Water Inlet Valve

Float Switch Kit

Don from Aptos, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench set

7 of 10 people found this instruction helpful.

Was this instruction helpful to you?

The motor was too loud

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.

Parts Used:

Dishwasher Circulation Pump And Motor

Conelis from Eclectic, AL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

front seal on the old pump failed causing the front bearing to get wet repeatedly and fail

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

Parts Used:

Dishwasher Circulation Pump And Motor

lisa from columbus, NE
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench set

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

One of the old stops broke

Snapped the new stops on. It took about 2 minutes.

Parts Used:

Dishwasher Rack Track Stop

Dwight from KENT, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Spinner button broke

Loosened 1 screw to access spinner button. Removed broken spinner button, replaced it with new button,snapped spinner and wedge on button ,replaced screw and was done in about 2 minutes. Thanks for the pictures of installation and the quick shipping of parts. Not to mention the money saved by doing it without a repairman. Thank you

Parts Used:

3rd Level Wash Spinner Kit

Richard K from Bloomington, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Fuse Blew

Took out the screws--found out what the problem was--ordered part (your people were helpfull--good customer people--received the part within the time I was told--installed according to the instructions--turned it on. . Working fine and guess what--I don't have to do the dishes anymore.

Parts Used: