Models > GTW460AMJ4WW > Instructions

GTW460AMJ4WW General Electric Washer - Instructions

All Instructions for the GTW460AMJ4WW
31 - 45 of 79
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washer would not start
unplugged old part plugged in new, took about 2 minutes.

this is a great web site, I didn't have to wait for a serviceman to come. and maybe not have the part and come back again. ........thanks
Parts Used:
LID LOCK SERVICE KIT
  • joseph from LAUGHLIN, NV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
8 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy operation....belt slipping.
Turned washer on to its side. Removed belt cover, three screws. Removed old belt. Cleaned both pulleys thoroughly, removing all traces of oil. Cleaned grooves thoroughly on motor pulley with small screwdriver. Installed new belt. Replaced cover. Turned washer upright.
Parts Used:
Drive Belt
  • james from BRONXVILLE, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking inlet value
Installing the inlet value was very easy the only thing was a very small "O" ring wasn't supplied with the value, so I removed the one on the leaking value. Not care must be taken not to damage the used "O"
The washer is running with no leaks
Thank you, for, saving me hundreds of dollars
Parts Used:
Water Inlet Valve Assembly
  • William from WILDOMAR, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Transmission leaking oil from seal. Separately the cold water solenoid was allowing drip I tub when not in use.
Replaced with new transmission platform. Unfortunately the seal is irreplaceable. Must have 1-5/16 inch wrench for tub nut (not 1-11/16).

Replaced with new water valve solenoid. Leak stopped. Yah!
Parts Used:
Water Inlet Valve Assembly Bearing Retainer & Fasteners Platform
  • Blair from EDMOND, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Socket set
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My son pryed the lid an broke it
I just took old one out an put new one in
Parts Used:
LID LOCK SERVICE KIT
  • Andrew from NAVARRE, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't wash rinse or spin
Not knowing for sure how to fit it I went to youtube for help watched a few videos and tested different things until I hit the right one .Moms washer is fixed.replaced lid lock,motherboard and pump I'm sure I don't need all those parts because when I found the code for the lid lock it started working
Parts Used:
MAIN CONTROL BOARD WITH CORE
  • Cynthia from PACE, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was shaking while on spin cycle
Extremely easy. You will need a helper to make it easy. The best directions are on you tube.
Parts Used:
ROD & SPRING Assembly LEFT - WHITE ROD & SPRING Assembly RIGHT - GREEN
  • Donn from FREDERICKSBRG, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Violent shake
You have to take the top off of the washer and the four suspension rods are at each corner. Fairly simple removal and installation of the rods. A quick you tube search is all it took. Easy peasy.
Parts Used:
ROD & SPRING Assembly LEFT - WHITE ROD & SPRING Assembly RIGHT - GREEN
  • Steve from Dexter, OR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
7 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid lock striker broke
Attached the lid striker with 2 screws to hold it in place
Parts Used:
Lid Lock Bezel
  • Allen from NASHVILLE, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Will not drain
The drain pump had three screws. Frist unplug the machine and turn the water off. And unplug the hose for the Hot and Clod Water. Make sure their no water in the tub. Unplug the pipe from the Tub. The unscrew the nut for the connector. Then unplug the connector and be careful not to damage plug for the connector. Press the plug connector with your finger or long nose pliers . Then just hook the new plumb and you all set.
Parts Used:
Pump Drain Assembly
  • Christopher from LYNN, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set, Wrench set
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Auger would spin in both directions but not spin while washing
Used a Phillips screw driver to lock the top and bottom of auger. Took a while to separate from base. Used another driver to remove old base and put the new one on with nut driver. Placed auger on base and turned to lock. Job done and works great.
Thanks
Parts Used:
AGITATOR BASE HYBRID ASSEMBLY AUGER
  • Robert from POTTSTOWN, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water wouldn't drain
Took the belt cover and then replaced the pump. Did a dry run and everything was fine.
Parts Used:
Pump Drain Assembly
  • Richard from DANBURY, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not start
The parts I ordered were made of junk plastic and did not match up with the the existing parts. The parts did not end up fixing the problem and I bought a new washer instead.

Waste of money
Parts Used:
LID LOCK SERVICE KIT LID LOCK SERVICE KIT
  • Jack from KENT, OH
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
6 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid lock blinks, washer will not operate
Put the parts in, turned washer on.....lid lock still blinks, will not operate. Suggest the control board that sends the signal to the solenoid lid lock switch is defective. Buying a new washer, scrapping this one.
Parts Used:
LID LOCK SERVICE KIT LID LOCK SERVICE KIT
  • Lawrence from VERHALEN, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
6 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water wouldn't drain
Replaced water pump. Washer now works as new.
Wife is now happy!
Parts Used:
Pump Drain Assembly
  • Kevin from ZOAR, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Socket set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTW460AMJ4WW
31 - 45 of 79