GTS18KHPDRCC General Electric Refrigerator - Instructions

TURN WATER OFF TO REFRIDGE. TURN OFF ELECTRICITY.

Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)

Use adapter for the electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.

PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.

HAVE A COCKTAIL!

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

Removed Ice Maker (2-Bolts)
Removed Ice Tray Screw Motor (to get to Ice Maker Plug- 4 small screws)
Installed new Ice Maker and reinstalled Ice Maker Screw Motor
Extreamly easy

Ice hopper had no ice in it. But water in door worked and if I added ice to hopper, it would dispense in door. I added water to ice maker but no ice was made. Replaced ice maker and all it required was to unplug harness and remove two screws with nut driver. Easy!

If a 74 year old guy can install an ice-maker in a 20 + year old fridge in 20, or so, minutes it must have had good pictures and BIG PRINT. Working quite well at this time!

It was as easy as the instructions were clear (and they were). Remove 2 screws and two nuts, pop out the old ice maker, pop in the new, plug in and tighten screws/bolts. It worked. I'm happy.

I removed the lower screw (not needed for the new icemaker), loosened the 2 top screws, unplugged the wire harness and removed the old icemaker. Unpacked the new icemaker assembly from the box, wiped the ice cube depressions to remove any debris, snapped on the water tube adapter, hung the new assembly on the 2 loosened upper screws and tightened the screws. The wire harness required the supplied pigtail plug which made the wire assembly long and awkward to replace the ice bucket/dispenser assembly, plugged it in and was done. It took a total of about 10 minutes for the entire operation and had a full bin of ice cubes within 36 hours and was ready for the ice dispenser/crusher in the freezer door. Easy install!

The parts were here the next day. After removing the old ice maker it was a simple installation using the adapter cord furnished. It took about 15 minutes. You have to work with the cord some to get it to fit behind the ice maker, but it does fit. The ice maker started up immediately & works great.

removed old ice maker, obtained part number from it. went on line ordered new ice maker at 10:45 in the morning, at 3:00 the nexte after noon new icemaker was in hand. took about 5 minutes to install new ice maker. works perfect. would do business again with this company.

Used the nutdriver to loosen two screws, life out ice maker, disconnect electric plug and put aside. Placed the new icemaker on the loosened screws, plugged in electric connector and tightened screws. Used small level to verify that unit was level.Waited about two hours for first cubes to be released into tray - has been working fine since!

I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i

It took longer to remove the ice bucket and frozen food than it did to replace the ice maker. Remove one screw with a 1/4" nut driver, slide outward and remove plug. transfer water tube to new unit. plug it in, slide into rear slots and install one screw. Replace ice bucket and frozen food, shut the door and hear ice falling in about 30 min. Easy job! Great product! THANKS MJS

Loosened 2 screws unplugged cable. Plugged in cable adapter on new unit. Plugged in to receptical, hung on 2 screws, tightened 2 screws. Done

My husband took the old icemaker out before the new one came in. When the new one arrived, I installed it in less than 10 minutes.

Removed the Ice maker from the freezer because the light was not on. Disassembled ice maker, found printed circuit board had shorted across two posts because the board was black in that area. Bought new ice maker assembly, installed in less than five minutes, making Ice fine.