GTR22KSSCRSS General Electric Refrigerator - Instructions

Very easy to order the part, perfect match, video was greatest help. Saved me over 200.00, what it would cost for a repair man Great place to get alliance parts.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

removed the inside fridge electrical panel and swapped switches

I removed cover above the light from the back of the freezer. I removed the fan and clipped the wire leads, after disconnecting the breaker to the fridge. I connected the wires with wire "union" from Radio Shack. Could have used wire nuts. I put the breaker on to check that it was running, then put the cover back on. However, to fix the build up of ice on the coils in the back of the freezer, I also replaced the thermisor and the heater coil after defrosting the coils with a hair dryer. Both were easy repairs and the fridge works fine.

easy pry out, disconnect wiring, connect on new switch and press in switch.

This was as easy as it comes and a whole heck of a lot cheaper than buying a new fridge. This is our second fridge, which we need but I hated the thought of buying another one. The old seal pulled off in 2.2 seconds and the new one snapped right in place. If it wasn't for the 5 minutes it took for me to get a couple of kinds out with a hairdrier, I would have completed the whole project in under 2 minutes, yes 120 seconds. It's that easy.

Pull the old off ..put new one on

condenser fan on bottom condenser not runningchanged fan and fan motor

took apart stat. area rplaced wire harness &t.stat simple but im a retired union electrican so wiring was a bit easy

I followed the instructions in the video regarding removal, repair and reinstall. It all went as the video said, except for the reinstall. The rear tab did not snick into place like the one in the video did, and it was extremely difficult to see whether or not it was inserted properly. I ended up inserting the rear tab by feel, and then I had to hold it in place while I stretched the front part of the frame to line up the screw hole in order to reinsert the screw. I had to have my wife hold the flashlight while I did that in order to see. Other than that, the repair went well, it is working like a charm, and I know I have a quality GE part in my refrigerator again! Many thanks to Partselect for their speediness in getting the part to me and giving me the needed information in getting the repair done! I will shop here again.

My compressor fan that blows over the coils was not spinning. I measured 120 VAC going to the fan so I knew it should have been spinning but wasn't. Took fan motor out and took it apart and super lubed the motor to get it spinning again temporarily until I could get the new one in. Put new one in and has been working for about 10 days now. Freezer is not below 0 deg F which is what you want. Frig is below 40 deg F also what you want.

I removed the ice marker first and took the back panel off using a nut driver. Be careful I had wires tied to the back panel, so I moved it like opening a door, right to left. The I removed the fan motor. Be careful not to damage the fan blades. I took the fan blades off and the dust cover. The dust cover was very tight. I had to use a very small screw driver to get it off. When I put the dust cover on the new motor I did not push it down tight. I turned the spindle of the new motor to make sure it turned. The put everything back. Turned it on and it worked. I put the ice marker on last. Take a note of how far the fan blades are on the spindle. The refrigerator now turns off more often.

Follow the instructions on the video. Took pictures removing Evaporator Fan Motor. Installed new motor in 44 minutes. Thank you part Slect

Empty the contents of the freezer.Take out the one shelf.Remove the plastic pieces covering the fan and evaporator removing 2 screws with the nut driver.Remove the metal back using the nut driver(2 screws)Remove the fan assembly from the back of the freezer.(4 screws)Remove the green ground wire from the fan assembly(1 screw) Take the fan assembly out of the freezer and remove the old fan(2 screws) and reinstall the new fan.Assemble the parts in the reverse order .Very simple and intuitive for anyone who is "handy" at all.

Just follow the instructions from the Youtube, the link to the video is included in the sheet coming with the part. It was easy to take the entire compartment out as instructed, however, after replace the old motor with the new one, it took more than 20 min to put the entire compartment back after trying different ways. It has been working greatly since it was repaired.