GTR22KSSCRSS General Electric Refrigerator - Instructions

WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.

Attempted to remove whole bracket per PartSelect YouTube video. Our refrig must have been slightly older or something, because the bracket would not come out no matter how much we begged and pleaded. ~ So we replaced motor in place, which was a headache, but doable. Seems to work fine, and much quieter than the old motor.

Simply followed the video -- VERY helpful... BUT: getting the bottom tab to re-insert into the holder after the motor was replaced was VERY difficult...!!! Until I discovered that I could move the refrigerant coil (upon which the tab mounts) just enough that I could get the tab inserted...!!! "Twas NOT as simple as it looked on the film...

Being able to move both the fan motor holder (with the tab) AND the coil made it happen, easily...

Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.

I watched the repair video on partselect's website for the condenser fan motor and realized I could do the repair. The hard part was putting the two screws back on the bracket to mount the fan. (they were not easy to get to with your hands let alone tools) other than that super easy and great experience!
Tom

I replaced the compressor fan.

Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.

Removed the fan blade then removed the motor. Replaced motora nd Installed fun blade.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

Laying on my side.

Attempted it on my own with the aid of the video on your site, but could not remove the fan shroud due to additional copper lines that prevented me from getting it out.
Gave up and called an appliance repair guy. He had a novel approach: Don't pull the fan shroud (with motor attached) out, but instead remove one of the screws holding the motor into the bracket, then bend the bracket to get the motor out.
All good until we powered the fridge on again. Now the fan works, but spins faster (and makes more noise than) the original fan.
The repair guy's comment: "I've seen that before with some of the aftermarket fans."
Nice! I'd appreciate getting the right part when I order the part from your website based on my fridge model number.

I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.