GSS25IYNZHFS General Electric Refrigerator - Instructions

ordered replacement part with the understanding that tubing to the water valve could be easily removed. The tubes were carefully removed with some difficulty, and when the new tubes were inserted one leaked. The tube seat was not snug. Therefore a new water valve was purchased. The installation was successful within about 20 minutes. If I were to do the job again, both the water resevoir and valve would be ordered together.

Removed the lower 2 drawers, lower front grill, rear lower compressor cover. Removed the 2 water lines from the quick connects and screws from the water tank. Pulled lines through the hole in the right rear of the refrigerator and removed tank. Then reversed steps to install new tank. The upper plastic tank cover has 2 buttons on top that are really screws with a plastic cap, these are easily removed with pliers.

Simply took the old drawer out, and slid the new one in. Took 30 seconds, and voila! All fixed.

I went to the internet and found parts select web site. Saw all of the possible fixes for my problem and read all of the other repair stories. My story actually became a journey that is still continuing. I first changed the water filter, but still no water at the dispenser. I next disconnected the coupling at the bottom of the freezer door that carries water to the dispenser and when the dispenser was depressed, water flowed at the coupling, but not at the dispenser. After reconnecting the coupling, I turned the freezer setting to 1 for 4-5 days, but still no water at the dispenser (possibly the line was frozen, but we had recently been away for a week and the water dispenser still supplied water at a freezer setting of 4). Now I am at the point of the journey into replacing parts one at a time to get water. First I ordered the dual water valve for the ice maker and water dispenser. I replaced this valve with instructions from Parts Select and still no water at dispenser. Next I ordered and replaced the switch at the dispenser lever and still no water. Next was the solenoid attached to the ice door, ordered, replaced and still no water at dispenser. I am now at the final part in this repair and that is the $132 circuit board. So I will be ordering this part soon and hopefully that will fix the issue.

after replacing the door seal, I couldn't get the new seal to close and stay closed, so I replaced the closing arm and spring. The door will close now but not tightly and it's loosing cold air. So I made and patented a wooden block to put behind the freezer door handle and the refrigerator door handle to keep the doors closed. Available in black, white and natural tan. (just kidding about the patented part, but not the block)

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

Removed ice bucket and emptied it, storing ice cubes temporarily in another container; Removed broken support and replaced with new. Removed rotor/crusher assembly from ice bucket assembly, replaced broken rotor (other vendor), reassembled ice bucket, filled with stored cubes and reinstalled in freezer.

There are three holes under the front panel in which you push a very small screwdriver in and the front panel comes off.In back of the panel is another panel with 4 screws .1 at each corner.Remove the 4 screws and that will come off exposing the working parts that need to be replaced.This is also a good time to clean anything you can get to in that area.It is very important to remember how everything came out.

remove the front plate. use screwdriver to pry the cover off from the bottom of the cover, remove the wiring from the front cover.remove the 4 screws and pull out the shute. remove three screws from the solonide and replace . very easy fix. save yourself $100.00 labor.

Followed instruction video. Replaced water tank, flushed line from house water. Reconnected line and cycled until tank filled. I have ice and water now.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Take off all , then install.. following the version..

1. Removed light cover.
2. Removed old light assembly board from cable, (1 of 3 lights).
3. Connected cable to light assembly board.
4. Replace light cover.
5. All 3 lights fully lighted.
6. Installation Completed.

First:
Remove all shelf’s and drawers from fridge inside that were on the way of the water tank
Second:
Pull the fridge from the wall
Turn off the water supply:
Unplugged the power supply
Third:
Remove the cardboard cover at bottom of the fridge on the back for better access to the water pipes
From the front remove the toe kick for better access at the water pipes
Disconnected the water pipe at the front left side, use a rag or paper towel to hold the water that may drip ( bigger pipe)
Remove the covers on the top of the water tank inside the fridge
Disconnected the water pipe at the back left side ( smaller pipe)
Unscrew the water tank (two screws)
Pull the water tank out with the water pipes attached
Fourth:
Install the new water tank assembly , make sure the pipes goes on the hole at the right side and reaches the from and back
Connect pipes until the line that shows on the pipes
Screw back the new water tank
Put the protections back on the top
Plug the fridge and open the water supply to make sure there is no water leaks
The water is ready to be use

The 2 wire baskets FZ with their handles replaced one shelf in the freezer. Thus there was improved utilization of the capacity. When we originally filled the freezer, it was obvious that about 2 cubic feet were not used. Part numbers are WR21x10060 and WR12x10626. A similar situation is in the refrigerator side. We added the snack drawer and shelf pan assy. (replacing one glass shelf) and the shelf module FF to the door. Part numbers are WR32x26244, WR71x10685 and WR71x38318. I had to work with Parts Select Customer Service to identify the correct parts since they are not on the BOM for this model, but are on BOM's for similar capacity refrigerators. The service representatives were very helpful.