GSS23GGKPCWW General Electric Refrigerator - Instructions

Removed broken switch with plastic scraper (press tension latch on bottom), moved two wire terminals to the new switch and pressed the new switch into the hole.

I was able to snap the new piece right in

1. Emptied the crisper pan,
2. Removed it from the refrigerator,
3. Flipped it upside down,
4. Removed the old one by pulling it off,
5. Replaced it with the new OEM part. and
6. Reversed the process.

Opened package and just snapped in front insert. Took longer to open package than it took to replace broken insert.

Very easy novice could do

I went to the internet and found parts select web site. Saw all of the possible fixes for my problem and read all of the other repair stories. My story actually became a journey that is still continuing. I first changed the water filter, but still no water at the dispenser. I next disconnected the coupling at the bottom of the freezer door that carries water to the dispenser and when the dispenser was depressed, water flowed at the coupling, but not at the dispenser. After reconnecting the coupling, I turned the freezer setting to 1 for 4-5 days, but still no water at the dispenser (possibly the line was frozen, but we had recently been away for a week and the water dispenser still supplied water at a freezer setting of 4). Now I am at the point of the journey into replacing parts one at a time to get water. First I ordered the dual water valve for the ice maker and water dispenser. I replaced this valve with instructions from Parts Select and still no water at dispenser. Next I ordered and replaced the switch at the dispenser lever and still no water. Next was the solenoid attached to the ice door, ordered, replaced and still no water at dispenser. I am now at the final part in this repair and that is the $132 circuit board. So I will be ordering this part soon and hopefully that will fix the issue.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Take off all , then install.. following the version..

NOTE:You can still use your Ice Maker as the water tank is for water dispenser only-only leaked if you pushed on water dispenser;We put painters tape over water dispenser until we got our water tank (Part# PS783769);easy install see below ;NOTE - WATCH VIDEO ON HOW TO INSTALL -ALTHOUGH NOT THE SAME UNIT AS MINE THE PROCEDURES ARE SIMILAR - A MUST
a. Remove food from bottom 3 drawers in refrigerator side so you can remove the drawers to access Water Tank
b. Turn off water
c. Take cardboard off back of Frig (bottom of Frig)
d. Find tubing (short one) that goes to water tank & remove where it connects to the union:located Left side bottom of back of Frig - Push in white lip to remove tubing
e. Remove grate from front of Frig (on bottom) removing 2 screws one far left & one far R (will have to open doors)
f. Find long tubing from Water Tank left side under Freezer door and pull out where it connects to union so you can work on it with Freezer door closed - Disconnect tubing by pushing in on white ring on Union to release tubing.
g. Removed 3 bottom drawers Frig side
h. Removed plastic guard from over light (just pull up on both ends to remove (16 1/2 in long)
i. Remove plastic over top of water tank
j. Remove foam from over top of water tank (be careful not to break foam
k. Take out 2 screws holding water tank
l. Pull out Water Tank and Tubing noting which hole short & long tubing comes out of
m. Install new Water Tank by pushing tubing into holes; Short goes in right hole & Long in left hole
n. Attach Water Tank with two screws you removed, attach foam, plastic cover over Water Tank then plastic over light
o. Short tubing will come out toward back and long hose needs to be pushed under frig toward front freezer door.
p. IMPORTANT NOTE - REMOVE PLUGS FROM TUBING where it connects to Union - I had to undo this part because I didn't notice the plugs
q. Connect Tubing - Short to rear Union by pushing in on white collar on union and do the same with the front long tubing
r. Turn water back on
s. Test Water dispenser to make sure it working before re-installing cardboard on back & grate on front - this is when I found out I forgot to REMOVE THE PLUS FROM THE TUBING
t. Install cardboard on back & grate on front
u. Put in shelves & food back into Frig
v. Because it's quick no need to move food from top shelves

1. Removed light cover.
2. Removed old light assembly board from cable, (1 of 3 lights).
3. Connected cable to light assembly board.
4. Replace light cover.
5. All 3 lights fully lighted.
6. Installation Completed.

Followed instruction video. Replaced water tank, flushed line from house water. Reconnected line and cycled until tank filled. I have ice and water now.

I just moved the moving parts from the Frame for the humidity level from old to new and all was OK

Clear freezer items in the area of repair as light assembly is in the back of the freezer. Suggest removing shelving in the same area to provide more working space. Utliize a small flashlight to provide interior lighting. Use a stubby phillips screwdriver to remove fastener securing the light cover.
Cover snaps out to remove light board assembly. Gently pull to disconnect the electrical connection to the light board. Then pull the light board assembly from the mounting posts securing the light board. Be careful not to snap either posts or the light board.
To install the new light board, I found it easier to connect the electrical source first, then push the light board onto the plastic posts to secure the light board. There are holes in the light board to insure a secure fit. Reinstall the light cover and reinstall the mounting screw. All done in less than 5 minutes!

My father called and asked me if I knew where he could get a new switch light for his refrigerator. I came across your web site and found the part right away. In less than 3 days the part came and my father put it on. He said it was easy and that it was great to have the part come to him instead of having to search all over town. Thanks so much for the fast, easy service.

First:
Remove all shelf’s and drawers from fridge inside that were on the way of the water tank
Second:
Pull the fridge from the wall
Turn off the water supply:
Unplugged the power supply
Third:
Remove the cardboard cover at bottom of the fridge on the back for better access to the water pipes
From the front remove the toe kick for better access at the water pipes
Disconnected the water pipe at the front left side, use a rag or paper towel to hold the water that may drip ( bigger pipe)
Remove the covers on the top of the water tank inside the fridge
Disconnected the water pipe at the back left side ( smaller pipe)
Unscrew the water tank (two screws)
Pull the water tank out with the water pipes attached
Fourth:
Install the new water tank assembly , make sure the pipes goes on the hole at the right side and reaches the from and back
Connect pipes until the line that shows on the pipes
Screw back the new water tank
Put the protections back on the top
Plug the fridge and open the water supply to make sure there is no water leaks
The water is ready to be use